American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

10 Techniques for Tighter, Faster, Stronger Miter Joints Erlanger KY

Long miters are a nightmare to clamp, but adding temporary triangular blocks makes it a snap. The key is to use paper from a grocery bag. Dab some wood glue on both sides of the paper, stick the blocks wherever you need them and let the glue set overnight.

The Home Depot
(859)331-4500
500 Clock Tower Way
Crescent Springs, KY
Hours
Mon-Sat: 7:00am-10:00pm
Sun: 8:00am-8:00pm

The Bromwell Company
(513) 621-0620
117 West Fourth Street
Cincinnati, OH

Data Provided by:
Indus Construction Products Inc.
(513) 241-1551
1455 Dalton Avenue
Cincinnati, OH

Data Provided by:
Finished Dimensions Inc.
(513) 353-4500
5445 State Route 128
Cleves, OH

Data Provided by:
Salem Door Company
(513) 552-3000
2120 Stapleton Drive
Cincinnati, OH

Data Provided by:
The Home Depot
(859)283-1460
99 Spiral Blvd
Florence, KY
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(859)572-0018
415 Crossroads Blvd
Cold Spring, KY
Hours
Mon-Sat: 7:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(513)661-2413
6300 Glenway Ave
Cincinnati, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Bushelman Supply Co.
(513) 771-9121
250 Marion Road
Cincinnati, OH

Data Provided by:
The Home Depot
(513)688-1654
520 Ohio Pike
Cincinnati, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

10 Techniques for Tighter, Faster, Stronger Miter Joints

10 Techniques for Tighter, Faster, Stronger Miter Joints

by Gary Wentz

Miter joints provide one main advantage over other joints: A miter joint hides end grain and brings face grain neatly together. Everything else about miter joints is a hassle. They’re fussy, time-consuming and easy to screw up. But there are ways to minimize those hassles.

Make Micro Adjustments with a Disc Sander

No tool can tweak a miter’s fit as easily as a disc sander can. You can shorten the workpiece a hair with a quick touch of the disc. You can also adjust the angle by a fraction of a degree. Instead of fussing with the miter gauge, make tiny adjustments by sticking a paper shim between the gauge and the workpiece. 

Knock-Off Blocks for Long Miters

Long miters are a nightmare to clamp, but adding temporary triangular blocks makes it a snap. The key is to use paper from a grocery bag. Dab some wood glue on both sides of the paper, stick the blocks wherever you need them and let the glue set overnight. When you’re done clamping, remove each block with a hammer blow. The paper creates a weak spot in the glue bond, so the blocks break away without damage to the wood. Use hot water to soften any paper or glue left on the wood, then scrape it away and sand as usual. 

Customize a Drafting Square

Drafting squares are inexpensive, accurate and great for tool or jig setup. Because they’re plastic, you can easily customize them to suit the job. We filed notches in this square to keep the saw teeth from interfering with setup. Drafting squares are available in various sizes for $4 to $10 at art and office supply stores. 


Guides for Perfect Edging

Mitered guides clamped in place let you perfect the length and angle of mitered edging. Use the edging stock itself to guide the fit of each piece. Clamp the guides precisely in place and work your way around the tabletop, gluing each perfected piece in place as you go. After you glue and clamp a section of banding, remove the adjoining guides immediately so you don’t accidentally glue them in place.


The Touch Test

When you’re building a box or frame, the opposite sides must be precisely the same length. Otherwise, even the most perfect miters won’t form a tight joint. To compare lengths, hold the parts together on a flat surface and feel the ends. Your finger can detect differences your eyes can’t. 

Stop Cutting Creep

When you’re cutting miters on a miter saw, the spinning blade tends to push or pull the workpiece along the fence. A hold-down clamp will stop the creeping, but molded stock can be hard to clamp. In that case, dampen the back side of the wood. Moistened wood is less slippery and easier to hold in place.


The 60-Second Squeeze

When you’re dealing with small or hard-to-clamp parts, ...

Click here to read the rest of the article from American Woodworker