American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » ยป

11 Drill Press Tips Circle Pines MN

A cradle provides continuous support for thematerial so the bit won't blast through the back, leaving a ragged exithole. To make the cradle, drill a hole the exact size of the roundstock in a small piece of scrap and then cut it in half. Mount the twohalves on a sheet of plywood to cradle the stock on each end.

The Home Depot
(763)717-0316
4550 Pheasant Ridge Dr
Blaine, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(763)571-9600
5650 Main St, NE
Fridley, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(651)464-5277
1943 W Broadway Avenue
Forest Lake, MN
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

Rockler Woodworking and Hardware #13
(651) 773-5285
1935 Beam Avenue
Maplewood, MN

Data Provided by:
The Home Depot
(763)533-1200
6701 Boone Ave North
Brooklyn Park, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(763)795-2060
99 Northtown Drive
Blaine, MN
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

The Home Depot
(763)422-1200
3550 124th Ave NW
Coon Rapids, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(651)770-9600
2360 White Bear Ave No
Maplewood, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(612)782-9594
1520 New Brighton Blvd
Minneapolis, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(763)494-0117
15800 Grove Circle North
Maple Grove, MN
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

Data Provided by:

11 Drill Press Tips

11 Drill Press Tips



If you tend to think of your drill press as a boring machine, you maynot be using it to its full potential. These tips will help you findnew ways to use your drill press and bring out its full potential as anindispensable woodworking tool


1. Prevent Clogged Bits

Keep drill flutes clear with a couple squirts of bitlubricant before you drill. This is especially helpful when you aredrilling deep holes. And you'll really notice the difference whendrilling into end grain, such as on the pen blanks shown here. Withouta lubricant, the flutes jam quickly, which can cause the blank, not tomention your temper, to rupture.

Source Grizzly Industrial, (866) 523-4777, www.grizzly.com
OptiCut XL bit lubricant, 4 oz., #H4870, $5.


2. Drill Without Blow-Out

Avoid blow-out on round stock by resting it in a half-round cradleinstead of a V block. A cradle provides continuous support for thematerial so the bit won't blast through the back, leaving a ragged exithole. To make the cradle, drill a hole the exact size of the roundstock in a small piece of scrap and then cut it in half. Mount the twohalves on a sheet of plywood to cradle the stock on each end.



3. Square the Table for Accuracy

Square the table using this old machinists' trick.Bend a piece of 1/4-in. steel rod (available at home centers) into an Sshape, as shown in the photo above. Mount it in the chuck and swing itby hand to each side of the table. Use a feeler gauge between the endof the rod and the tabletop to test the clearance at each end of thetable. Adjust the table tilt until there's .003 in. or less differencebetween the two sides.


4. Find the Center

Perfectly center a hole by placing one face of yourworkpiece against a fence and dimpling the surface with the tip of thedrill bit. Then rotate the workpiece end for end and dimple it again.If the two dimples don't line up, as shown here, the fence needs to berepositioned. To center the hole, move the fence by half the distancebetween the two dimples.


5. Drill Equally Spaced Holes

Drill a series of equally spaced holes using a set of flip stops.For the cribbage board shown here, each stop is made of 1/4-in.hardboard. Flip one stop for individual hole spacing, two for the largespace between groups of holes.





6. Sand Contours

Shape parts on your drill press using an inflatabledrum sander. You can adjust the stiffness of the drum by adding orremoving air. Pumped up, it acts like a typical drum sander. Drain someair out and the sander will conform to the shape being pressed againstit, gently rounding the corners, as shown in the photo above. The drummounts to a metal base clamped to your table. The base minimizeslateral stress on your drill press spindle.

Source Woodworkers Supply, (800) 645-9292, www.woodworker.com
Pneumatic drum sander kit, including paper and base, #947-499, $70.



7. Center a Hole in a Sphere

Click here to read the rest of the article from American Woodworker