American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

11 Drill Press Tips San Angelo TX

A cradle provides continuous support for thematerial so the bit won't blast through the back, leaving a ragged exithole. To make the cradle, drill a hole the exact size of the roundstock in a small piece of scrap and then cut it in half. Mount the twohalves on a sheet of plywood to cradle the stock on each end.

The Home Depot
(325)223-0439
4363 Houston Harte Exwy
San Angelo, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Fastenal- San Angelo
325-486-1626
701 Knickerbocker Rd San Angelo, TX, 76903
San Angelo, TX
 
Lowe's
(325) 942-3100
5301 Sherwood Way
San Angelo, TX
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

LOWE'S OF SAN ANGELO, TEX.
325 942-3100
5301 SHERWOOD WAY SAN ANGELO, TX, 76904
San Angelo, TX
 
Home Depot
(361) 853-9173
4014 S Port Ave
Corpus Christi, TX
 
Southern Fastening Systems- San Angelo
915-944-8091
922 Arroyo Drive San Angelo, TX, 76903
San Angelo, TX
 
Angelo Bolt & Industrial Supply
325-655-0075
808 Warehouse Road San Angelo, TX, 76903
San Angelo, TX
 
Westlake Ace Hardware
(325) 942-6602
1821 Knickerbocker Rd
San Angelo, TX
 
Sunset Mall
(325) 942-5281
4000 Sunset Mall
San Angelo, TX
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18

The Home Depot
(432)368-9118
5181 E 42nd St
Odessa, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

11 Drill Press Tips

11 Drill Press Tips



If you tend to think of your drill press as a boring machine, you maynot be using it to its full potential. These tips will help you findnew ways to use your drill press and bring out its full potential as anindispensable woodworking tool


1. Prevent Clogged Bits

Keep drill flutes clear with a couple squirts of bitlubricant before you drill. This is especially helpful when you aredrilling deep holes. And you'll really notice the difference whendrilling into end grain, such as on the pen blanks shown here. Withouta lubricant, the flutes jam quickly, which can cause the blank, not tomention your temper, to rupture.

Source Grizzly Industrial, (866) 523-4777, www.grizzly.com
OptiCut XL bit lubricant, 4 oz., #H4870, $5.


2. Drill Without Blow-Out

Avoid blow-out on round stock by resting it in a half-round cradleinstead of a V block. A cradle provides continuous support for thematerial so the bit won't blast through the back, leaving a ragged exithole. To make the cradle, drill a hole the exact size of the roundstock in a small piece of scrap and then cut it in half. Mount the twohalves on a sheet of plywood to cradle the stock on each end.



3. Square the Table for Accuracy

Square the table using this old machinists' trick.Bend a piece of 1/4-in. steel rod (available at home centers) into an Sshape, as shown in the photo above. Mount it in the chuck and swing itby hand to each side of the table. Use a feeler gauge between the endof the rod and the tabletop to test the clearance at each end of thetable. Adjust the table tilt until there's .003 in. or less differencebetween the two sides.


4. Find the Center

Perfectly center a hole by placing one face of yourworkpiece against a fence and dimpling the surface with the tip of thedrill bit. Then rotate the workpiece end for end and dimple it again.If the two dimples don't line up, as shown here, the fence needs to berepositioned. To center the hole, move the fence by half the distancebetween the two dimples.


5. Drill Equally Spaced Holes

Drill a series of equally spaced holes using a set of flip stops.For the cribbage board shown here, each stop is made of 1/4-in.hardboard. Flip one stop for individual hole spacing, two for the largespace between groups of holes.





6. Sand Contours

Shape parts on your drill press using an inflatabledrum sander. You can adjust the stiffness of the drum by adding orremoving air. Pumped up, it acts like a typical drum sander. Drain someair out and the sander will conform to the shape being pressed againstit, gently rounding the corners, as shown in the photo above. The drummounts to a metal base clamped to your table. The base minimizeslateral stress on your drill press spindle.

Source Woodworkers Supply, (800) 645-9292, www.woodworker.com
Pneumatic drum sander kit, including paper and base, #947-499, $70.



7. Center a Hole in a Sphere

Click here to read the rest of the article from American Woodworker