American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

12 Tips for Better Biscuit Joining Lake Villa IL

Gauge blocks are handy for cutting double biscuit joints. Cutthe first slot with the joiner base referenced off the work surface.Then, use a spacer block under the joiner base for the second cut. Thegauge block eliminates the hassle and confusion of flipping your stockor resetting the fence. Make a whole set and you'll be covered for anybiscuit-spacing need.

The Home Depot
(847)223-0336
2050 N Illinois Rt 83
Round Lake Beach, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(847)599-0180
6625 Grand Ave
Gurnee, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(847)625-1020
2001 Belvedere Rd
Waukegan, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(815)385-9503
2461 N Richmond Rd
McHenry, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(847)726-0707
670 S Rand Road
Lake Zurich, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(847)973-8196
2731 Hartigan Rd
Volo, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(847)566-6532
3200 West Route 60
Mundelein, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Russell Mill
(847) 395-5190
15780 W Russell Rd
Zion, IL

Data Provided by:
The Home Depot
(847)549-0110
493 N Milwaukee Ave
Vernon Hills, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(815)479-1030
4447 US Route 14
Crystal Lake, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

12 Tips for Better Biscuit Joining

12 Tips for Better Biscuit Joining



1.  Make Corner Splines

 

Decorative corner splines sure make an ordinary box look great. Butthey can be a bit dicey to cut on a tablesaw. Let your biscuit joinercome to the rescue. A simple jig holds the box and the joiner so youcan cut slots quickly with minimal setup hassles. The jig is nothingmore than a piece of scrap plywood with two wood strips set at 90degrees to each other. A cradle fits around the plate joiner base andkeeps it from rocking on the box corner. The cradle is indexed to thejig with a couple dowels. Use spacer blocks to adjust the splinespacing. Plunge the joiner into the wood slowly to prevent tear-outwhere the blade exits the wood. With this box, you only need one spacerblock; just flip the box over to cut the upper slot.




2.  Preserve Your Biscuits With Kitty Litter



Nothing is more aggravating than a biscuit that won't fit into aslot-except maybe a whole bag of biscuits that won't fit. Biscuitsswell as they absorb moisture, whether from glue or the air. To preventswollen biscuits, store them with a desiccant, such as kitty litter.The kitty litter absorbs moisture and keeps the air inside thecontainer dry. Pour a small amount of kitty litter (the crystallinevariety is less messy) onto a cloth, tie it up and toss it into thecontainer. No more fat biscuits and they'll always smell nice.


3.  Highlight Cast-In Marks On Your Joiner



The cast-in alignment marks on a joiner can be difficult to read.If you're tired of squinting, use a permanent marker to highlight themarks. The difference it makes will amaze you.


4.  Apply Glue With An Acid Brush



Glue must be evenly applied throughout the biscuit slot to getthe strongest joint possible. The easiest way? Squirt some glue intothe slot and then run a glue brush, sometimes called an acid brush,through the slot until the glue is evenly coated on both sides and thebottom.

Source: Highland Hardware, (800) 241-6748
www.highlandhardware.com
Glue brushes, #166025, $3 for 10; #107792, $10 for 50.



5.  Use Gauge Blocks For Double Biscuit Joints



Gauge blocks are handy for cutting double biscuit joints. Cutthe first slot with the joiner base referenced off the work surface.Then, use a spacer block under the joiner base for the second cut. Thegauge block eliminates the hassle and confusion of flipping your stockor resetting the fence. Make a whole set and you'll be covered for anybiscuit-spacing need.


6.  Run Biscuits Long In Narrow Frames



You don't have to own a mini-biscuit joiner to assemble narrowframes. If possible, simply shift the slots so the larger biscuitextends into areas where it won't be seen, for example, the top orbottom of a face frame. After the glue has dried, cut the protrudingbiscuit with a handsaw. Then flush-trim with a router or sa...

Click here to read the rest of the article from American Woodworker