American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

12 Tips for Successful Gluing Hattiesburg MS

Make sure your clamps are ready before you glue. Unscrew the handles until you have a maximum amount of thread available. Sticky clamps can slow you down. Slide the sliding head on a small bar clamp or the tail stop on a pipe clamp to make sure it moves freely.

The Home Depot
(601)296-1098
4100 O'Ferrell Street
Hattiesburg, MS
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Turtle Creek Mall
(601) 271-4600
1000 Turtle Creek Dr
Hattiesburg, MS
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:11-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:11-18

Classic Concepts/Homectr
(601) 271-8111
6610 Us Hwy 98 W, INSIDE CLASSIC CONCEPTS
Hattiesburg, MS
 
Fastenal- Hattiesburg
601-544-4888
1517 North Main Street Hattiesburg, MS, 39401
Hattiesburg, MS
 
Lowe's
(601) 584-4066
40 Tyner Road
Petal, MS
Hours
M-SA 7 am - 9 pm
SU 8 am - 7 pm

LOWE'S OF HATTIESBURG, MISS.
601 261-3008
6004 US HIGHWAY 98 HATTIESBURG, MS, 39402
Hattiesburg, MS
 
Fastenal- Hattiesburg
601-544-8990
4315 Hwy 49 Hattiesburg, MS, 39402
Hattiesburg, MS
 
Lowe's
(601) 261-3008
6004 Us Hwy. 98
Hattiesburg, MS
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Lowe's of Petal
601-584-4066
40 Tyler Rd Petal, MS, 39465
Petal, MS
 
ACE HARDWARE OF PETAL, INC.
(601) 544-6111
401 S Main St, Located in the old Fred's Building
Petal, MS
 

12 Tips for Successful Gluing

12 Tips for Successful Gluing

by Tom Caspar

Do a Dry Fit

Clamp your pieces without glue to make sure the joints come together tightly. This step also serves as a test for your choice of clamps and blocks. Here, a dry run revealed that I need wedge-shaped strips and a spacer to clamp these tapered legs.

Prepare the Glue Brush

If you use a brush, remove any loose bristles. Acid brushes  are inexpensive and work well, but you should cut the bristles to about half their length to more easily control where the glue goes. You can find these brushes at a hardware store.

Prepare a Cleanup Tool

It’s best to remove glue squeeze-out before it hardens. Use a clean putty knife on wide surfaces and a freshly sharpened stick in corners. Wipe them often on a damp rag.

Protect Your Wood

Small clamp heads can put big dents in your project. Make sure you’ve got blocks, strips or pads handy to place between the clamp heads and the project’s parts. I prefer to make blocks from a soft wood, such as pine, to avoid crushing my project. 

Avoid Black Stains

Iron pipes leave black stains on your wood if they directly contact glue squeeze-out. Run a strip of masking tape along the length of each clamp to prevent this problem. Galvanized pipes don’t require taping.

Fix Too-Tight Joints

If you must pound parts together, the joints are probably too tight. Tenons swell a bit when you add glue, which makes a tight joint more difficult to assemble. The most accurate way to pare a tenon is using a rabbet plane. Its iron is the full width of the plane’s body, so it can cut up to the tenon’s shoulder.

Clean Your Bottle’s Applicator 


If your glue bottle’s cap is clogged with congealed glue, soak it in a jar of very hot water for 15 minutes or so. This softens hardened glue, making it easier to remove. 

Check the Glue


If you’re uncertain about your glue’s age, test its bond strength. Glue together two small scraps that are each about 1 in. wide, clamp and let dry 24 hours. Hit one piece with a hammer. If the two pieces shear apart with no fibers from one piece stuck to the other, your glue is probably too old. Replace it.

Arrange Your Clamps and Parts

Keep handy all the clamps and blocks you used in the dry fit. Arrange them so each is oriented correctly. Place all your parts in a logical order, so you can assemble them in sequence. Just remember—don’t panic.

Adjust Your Clamps

Make sure your clamps are ready before you glue. Unscrew the handles until you have a maximum amount of thread available. Sticky clamps can slow you down. Slide the sliding head on a small bar clamp or the tail stop on a pipe clamp to make sure it moves freely.

Get Ready for a Mess


A cotton rag and a jug of warm water are handy for wiping up spilled glue or lots of squeeze-out. I cut out the side of ...

Click here to read the rest of the article from American Woodworker