American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

3 Great Router Jigs Duncan OK

This Dadoing Jig takes the guesswork out of routing dadoes, because setting the exact width is virtually foolproof. Being able to tailor the dadoes' width to precisely match the thickness of shelves is a real blessing when you’re building cabinets with hardwood plywood, which is always undersize in thickness.

Fastenal- Duncan
580-252-9212
1504 W. Spruce Ave Duncan, OK, 73533
Duncan, OK
 
Ace Hardware
(580) 255-3500
1713 N Highway 81, Elk Plaza
Duncan, OK
 
The Home Depot
(405)749-1590
14201 N Pennsylvania Ave
Oklahoma City, OK
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(405)330-0151
1901 S Broadway
Edmond, OK
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(918)376-9975
9450 N 129th East Ave
Owasso, OK
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Duncan - Auth Hometown
(580) 252-5106
3001 N Highway 81
Duncan, OK
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-18.5
Tue:9-18.5
Wed:9-18.5
Thu:9-18.5
Fri:9-18.5
Sat:9-18.5
Sun:11.5-16.5
Store Features
Mon:9-18.5
Tue:9-18.5
Wed:9-18.5
Thu:9-18.5
Fri:9-18.5
Sat:9-18.5
Sun:11.5-16.5

The Home Depot
(918)583-3400
901 S Elgin Avenue
Tulsa, OK
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(918)632-0069
4041 S Sheridan
Tulsa, OK
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(405)737-3410
1600 S Sooner Road
Midwest City, OK
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(580)332-4018
515 J A Richardson Blvd
Ada, OK
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

3 Great Router Jigs

3 Great Router Jigs

Make your router a workshop workhorse.

by Tim Johnson

If you only use your router to rout decorative edges, you’re missing the boat. Your router can be the most versatile tool in your shop. The secret to unlocking your router’s potential is to use it with specialized jigs. A dovetail jig is a perfect example: With this jig, your router can do the same job as an expensive dovetailing machine. 

Fortunately, you can make many useful router jigs in your shop without spending an arm and a leg. I’ll show you three simple jigs that will expand your woodworking capabilities by leaps and bounds: one for dadoing, one for mortising and one for making shelf pin holes. Although these jigs have been around since the dawn of routers, they’re indispensable additions to any woodworking shop. 

Dadoing Jig

This jig (Fig. A, below) takes the guesswork out of routing dadoes, because setting the exact width is virtually foolproof. Being able to tailor the dadoes’ width to precisely match the thickness of shelves is a real blessing when you’re building cabinets with hardwood plywood, which is always undersize in thickness. 

This jig accommodates wood up to 24 in. wide. Its double T-square design guarantees dadoes that are square to the edges on both left and right cabinet sides. Positioning the jig couldn’t be easier—just line up the fixed fence with the top of each dado. This jig must be used with a pattern bit (see photo, left, and Sources, page 43). This combination is perfect for use with nominal 3/4-in.-thick plywood. It allows routing dadoes from 5/8 to 1-1/8 in. wide and up to 1/2 in. deep.

Make the Jig

1. Glue and screw the fixed fence (A) to the rails (B). Make sure the joints are perfectly square. 

2. Rout the slots in the adjustable fence (C) on a router table, using the router table’s fence and a 5/16-in. straight bit. 

3. Use the adjustable fence’s slots to locate the rails’ carriage bolt holes. Lay the fence on the jig, snug against the fixed fence and flush with the rails. Using a pencil, transfer the slot locations to the rails. 

4. Drill and counterbore the holes.

5. Install the carriage bolts. 

A pattern bit is a flush-trim bit with the bearing mounted on the shaft.  

Use The Jig

Photo 1: Position the fixed fence on a line indicating the top of each dado. Always orient the jig with the fixed fence at the top of the workpiece. Make sure the jig’s rail is firmly seated against the edge. Then clamp both pieces to your bench. 

Both rails are square to the fixed fence, so it doesn’t matter which rail registers the jig. Out of habit, though, I always register the jig against the front edge of the workpiece. 

Photo 2: Set the adjustable fence using offcuts from your shelves as spacers. This method guarantees that the dadoes will be exa...

Click here to read the rest of the article from American Woodworker