American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

3 Great Router Jigs Hastings NE

This Dadoing Jig takes the guesswork out of routing dadoes, because setting the exact width is virtually foolproof. Being able to tailor the dadoes' width to precisely match the thickness of shelves is a real blessing when you’re building cabinets with hardwood plywood, which is always undersize in thickness.

Kmart 7484 / Cross Merch
(402) 461-4460
3001 West 12Th Suite 3
Hastings, NE
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Allens Of Hastings Tv
(402) 463-5633
1115 W 2nd
Hastings, NE
 
Johnson Cashway Lumber Company
(402) 463-6602
2525 W 2nd
Hastings, NE
 
The Home Depot
(402)331-2879
712 N Washington St
Papillion, NE
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-7:00pm

The Home Depot
(402)333-9477
12710 L Street
Omaha, NE
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Big G Ace Hardware
(402) 462-5181
3203 Osborne Dr W
Hastings, NE
 
Hastings -Auth Hometown
(402) 463-8664
930 South Burlington Ste 300
Hastings, NE
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9.5-19
Tue:9.5-19
Wed:9.5-19
Thu:9.5-19
Fri:9.5-19
Sat:9-18
Sun:12-17
Store Features
Mon:9.5-19
Tue:9.5-19
Wed:9.5-19
Thu:9.5-19
Fri:9.5-19
Sat:9-18
Sun:12-17

Fastenal- Hastings
402-462-9700
100 West J Street Hastings, NE, 68901
Hastings, NE
 
The Home Depot
(402)964-9700
3950 North 144th St
Omaha, NE
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(402)573-6393
4545 North 72nd Street
Omaha, NE
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

3 Great Router Jigs

3 Great Router Jigs

Make your router a workshop workhorse.

by Tim Johnson

If you only use your router to rout decorative edges, you’re missing the boat. Your router can be the most versatile tool in your shop. The secret to unlocking your router’s potential is to use it with specialized jigs. A dovetail jig is a perfect example: With this jig, your router can do the same job as an expensive dovetailing machine. 

Fortunately, you can make many useful router jigs in your shop without spending an arm and a leg. I’ll show you three simple jigs that will expand your woodworking capabilities by leaps and bounds: one for dadoing, one for mortising and one for making shelf pin holes. Although these jigs have been around since the dawn of routers, they’re indispensable additions to any woodworking shop. 

Dadoing Jig

This jig (Fig. A, below) takes the guesswork out of routing dadoes, because setting the exact width is virtually foolproof. Being able to tailor the dadoes’ width to precisely match the thickness of shelves is a real blessing when you’re building cabinets with hardwood plywood, which is always undersize in thickness. 

This jig accommodates wood up to 24 in. wide. Its double T-square design guarantees dadoes that are square to the edges on both left and right cabinet sides. Positioning the jig couldn’t be easier—just line up the fixed fence with the top of each dado. This jig must be used with a pattern bit (see photo, left, and Sources, page 43). This combination is perfect for use with nominal 3/4-in.-thick plywood. It allows routing dadoes from 5/8 to 1-1/8 in. wide and up to 1/2 in. deep.

Make the Jig

1. Glue and screw the fixed fence (A) to the rails (B). Make sure the joints are perfectly square. 

2. Rout the slots in the adjustable fence (C) on a router table, using the router table’s fence and a 5/16-in. straight bit. 

3. Use the adjustable fence’s slots to locate the rails’ carriage bolt holes. Lay the fence on the jig, snug against the fixed fence and flush with the rails. Using a pencil, transfer the slot locations to the rails. 

4. Drill and counterbore the holes.

5. Install the carriage bolts. 

A pattern bit is a flush-trim bit with the bearing mounted on the shaft.  

Use The Jig

Photo 1: Position the fixed fence on a line indicating the top of each dado. Always orient the jig with the fixed fence at the top of the workpiece. Make sure the jig’s rail is firmly seated against the edge. Then clamp both pieces to your bench. 

Both rails are square to the fixed fence, so it doesn’t matter which rail registers the jig. Out of habit, though, I always register the jig against the front edge of the workpiece. 

Photo 2: Set the adjustable fence using offcuts from your shelves as spacers. This method guarantees that the dadoes will be exa...

Click here to read the rest of the article from American Woodworker