American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

3 Kitchen Storage Projects Horn Lake MS

Measure the frame opening and cut the base (A) 1/4 in. narrower (Fig. A, page 67). Make the drawers 1 in. narrower than the opening between the partitions. Cut and assemble the base assembly (A, B) and drawer parts (C, D, E). Sand and apply two coats of finish to the base and drawers.

The Home Depot
(662)349-6080
7260 Interstate Blvd
Horn Lake, MS
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(901)722-3535
1627 Poplar Avenue
Memphis, TN
Hours
Mon-Sat: 7:00am-9:00pm
Sun: 8:00am-7:00pm

The Home Depot
(901)818-0266
800 Truse Road
Memphis, TN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(901)379-1535
4950 Stage Road
Memphis, TN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Fastenal- Southaven
662-393-2949
1868 First Commercial Drive Southaven, MS, 38671
Southaven, MS
 
The Home Depot
(662)890-9470
7740 Craft Goodman Rd
Olive Branch, MS
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(901)546-0226
3469 Riverdale Rd
Memphis, TN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Colco Fine Woods & Tools
(901) 452-9663
2631 Jackson Ave.
Memphis, TN

Data Provided by:
Lowe's
(662) 536-3245
178 Goodman Road West
Southaven, MS
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

LOWE'S OF SOUTHAVEN, MS
662 536-3245
178 GOODMAN ROAD WEST SOUTHAVEN, MS, 38671
Southaven, MS
 
Data Provided by:

3 Kitchen Storage Projects

3 Kitchen Storage Projects

Squeeze more space from your cabinets with customized roll-outs.

by Eric Smith and David Radke

It may seem like a paradox, but even kitchens that are overflowing have underutilized space. Many base cabinets are only half used, because the back is inaccessible, stuffed with long-forgotten items you can’t see unless you get down on your knees with a flashlight. Here’s a set of pull-outs that bring everything within reach. 

Under-Sink Storage

To begin, measure the areas of open space around the plumbing. You may only be able to put a single pull-out on one side, or you may have to shorten them or build them around pipes coming up through the base.

Materials 

To make the trays shown here, you’ll need a half sheet of 3/4-in. hardwood plywood, 2-ft. x 2-ft. of 1/2-in. plywood, 17 lineal ft. of 1-in. x 4-in. maple, 2 lineal ft. of 1-in. x 6-in. maple, four pairs of 20-in. full-extension ball-bearing slides, a box of 1-5/8-in. screws, wood glue and construction adhesive.

Bottom Pull-Outs

Measure the frame opening and cut the base (A) 1/4 in. narrower (Fig. A, page 67). Make the drawers 1 in. narrower than the opening between the partitions. Cut and assemble the base assembly (A, B) and drawer parts (C, D, E). Sand and apply two coats of finish to the base and drawers. 

Set the drawer slides on 3/4-in. spacers flush with the front edge of the partition (B). Screw them to the partitions; then pull out the drawer members. Set the drawer members on the same 3/4-in. spacers to create the proper bottom clearance for the tray, and screw them to the sides of the trays flush to the fronts. Screw the base assembly to the bottom of the cabinet (Photo 1). Slide in  the drawers. 

Side-Mounted Pull-Outs

Make the side support cleats (K) so they sit flush or slightly proud of the face frame. Check for hinges that might get in the way of the pull-out tray. Assemble the trays with glue and screws. Apply finish. 

Attach the slides and mount them in the cabinet (Photos 2 and 3). Scuff the cabinet side with sandpaper and use construction adhesive and screws to hold the cleats. Cabinet sides are often finished, so screws alone may not hold well.

Bottom Pull-Outs

Photo 1: Build and install a base assembly for the bottom pull-outs. Center the base assembly in the cabinet just behind the hinges. Align the front edge with the face frame and screw it to the bottom of the cabinet. 

Photo 2: Install the slides on the side pull-out trays. Center a 3-1/2-in. template on the cleat and the tall side of each tray and trace the edges. Center the mounting holes of the slides on these lines.

Photo 3: Attach the support cleats to the side of the cabinet using screws and construction adhesive. Use a temporary plywood spacer to hold each cleat in position.

Mini-Pantry

These pull-outs bring boxes, jars and cans within easy reach.

Click here to read the rest of the article from American Woodworker