American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

3 Tapered Legs on the Jointer Grand Forks ND

Position the start block on the infeed table using the alignment mark as a reference (Photo 1). The start block gives you a consistent start point for each cut and provides a pivot point for safely lowering the leg blank onto the jointer.

Columbia Mall
(701) 787-9300
2800 S Columbia Rd
Grand Forks, ND
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18

ACME TOOLS- Grand Forks
(701) 746-6481
1705 13th Ave North Grand Forks, ND, 58203
Grand Forks, ND
 
Fastenal- Grand Forks
701-775-0851
2703 Valley Circle Grand Forks, ND, 58203
Grand Forks, ND
 
Kmart 4022 / Cross Merch
(701) 772-6676
1900 S Washington St
Grand Forks, ND
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Lumber Mart Inc
(218) 773-1151
1910 Business Hwy 2
E Grand Forks, MN
 
Burggraf's Ace Hdw/Paint
(701) 738-0455
1826 S Washington St
Grand Forks, ND
 
Lumber Mart West
(701) 772-1152
1901 32nd Avenue S.
Grand Forks, ND
 
Simonson Lumber & Hdw True Value
(701) 775-4292
820 3rd St N
Grand Forks, ND
 
Lowe's
(701) 765-9000
4001 32Nd Avenue South
Grand Forks, ND
Hours
M-SA 7 am - 9 pm
SU noon-8 pm

Simonson Lumber & Hardware True Value
(800) 642-7392
820 3Rd Street North
Grand Forks, ND

Data Provided by:
Data Provided by:

3 Tapered Legs on the Jointer

3 Tapered Legs on the Jointer

Advanced jointer techniques yield smooth, consistent tapers.

By Seth Keller

After I learned to cut tapered legs on the jointer, I never went back to my bandsaw or tablesaw. Legs cut on the jointer take less time and, best of all, require a whole lot less sanding. This is especially true with the spade-foot design in which the jointer’s cutterhead automatically creates the sweep above the spade foot. The same leg cut on a bandsaw would require hand shaping and sanding to finish the profile.

All three legs shown here are made from 1-3/4 x 1-3/4 x 29 in. stock. The first leg I’ll explain how to make is the familiar long taper found in many Shaker designs. Often, this leg has the taper on only two adjoining faces. The second leg has a short taper used on cabinets with legs and on some stylized modern pieces. The last profile, a tapered leg with a spade foot, builds on the techniques used in making the first two legs. This remarkable shape is both elegant and refined. It hints at Hepplewhite and Sheraton furniture designs from the eighteenth century and can make a piece distinctive and stylish even today.

The technique involves dropping a leg down on a running jointer. That may seem a bit scary at first, but stop and start blocks make the procedure safer than with most tablesaw taper jigs I’ve used and more accurate than for any taper I’ve done on a bandsaw.

It is a good idea to use a test leg to set up the cuts. As always, mill the mortises before you shape the legs. Finally, make sure your knives are sharp and your jointer is well-tuned.

Long Taper

1. Lay out the desired taper on all four sides of the leg. Make alignment marks 1 in. below the top of the taper. My taper goes from 0 in. to 1/2 in. at the foot.

2. Position the start block on the infeed table using the alignment mark as a reference (Photo 1). The start block gives you a consistent start point for each cut and provides a pivot point for safely lowering the leg blank onto the jointer.

Photo 1:  To set the start block, position the leg blank on the jointer with the alignment mark centered over the cutterhead. The alignment mark is placed 1 in. below where you want the taper to begin. Butt the start block up to the leg and clamp the block onto the infeed table.

3. Set your jointer’s depth of cut to 1/8 in. With push sticks ready, turn on the jointer. Place the foot of the leg firmly against the start block. Swing the guard out of the way and lower the leg (Photo 2).

Photo 2:  Start the taper cut by slowly lowering the leg onto the jointer with the foot set against the start block. Almost no wood is cut when you first put the leg stock down. The start block prevents kickback. Have your push sticks ready.

4. Complete the cut (Photo 3). Make three or four passes on the same side of the leg, closing in on your layout line.

Photo 3: Create the taper in several passes. Feed the leg slowl...

Click here to read the rest of the article from American Woodworker