American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

7 Trim Router Tips Camden NJ

Trim router motors range from 3.8 to 7.5 amps and run at speeds as high as 30,000 rpm. Add a base and the trim router weighs between 3 and 4-1/2 lbs. All models use only a 1/4-in. collet. You can buy a variety of bases and accessories (see Sources, page 4). Prices range from $80 for just the router with a standard base to $250 for a kit with several accessories.

The Home Depot
(215)744-1128
2539 Castor Avenue
Philadelphia, PA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

A to Z Exotic Hardwoods
(215) 432-5453
2527 Appletree Street
Philadelphia, PA

Data Provided by:
The Home Depot
(856)317-2001
2160 Route 70 West
Cherry Hill, NJ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(856)547-9600
310 Whitehorse Pike
Lawnside, NJ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(215)881-9600
2385 Cheltenham Ave
Philadelphia, PA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(215)218-0600
1651 S Columbus Blvd
Philadelphia, PA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(215)551-1753
2200 Oregon Avenue
Philadelphia, PA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(215)537-6100
4640 Roosevelt Blvd
Philadelphia, PA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-10:00pm

The Home Depot
(856)374-7700
1370 Hurffville Rd
Deptford, NJ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(856)234-0880
1200 Nixon Dr
Mount Laurel, NJ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

7 Trim Router Tips

7 Trim Router Tips



Laminate trim routers are amazing little machines. Their light weight and compact size make them exceptionally easy to use. Although they are designed primarily for trimming plastic laminate (p-lam), they also work great for light-duty wood routing.

Trim router motors range from 3.8 to 7.5 amps and run at speeds as high as 30,000 rpm. Add a base and the trim router weighs between 3 and 4-1/2 lbs. All models use only a 1/4-in. collet. You can buy a variety of bases and accessories (see Sources, page 4). Prices range from $80 for just the router with a standard base to $250 for a kit with several accessories.

Understanding what each of these accessories is capable of doing is the secret behind getting the most from your trim router. These accessories make the trim router very precise.

1. Protect the Plastic Laminate
Apply a lubricant, such as wax, soap or Trim Ease (a commercial product available from p-lam and trim bit distributors), to the plastic laminate's face when you use self-piloting bits. The lubricant protects the p-lam from burning or marring. Self-piloting bits are available in flush-trim or bevel-trim profiles. The flush trim (shown here) is used when you want to leave a flat, square corner. Its single cutting flute makes it fast-cutting. A solid carbide self-piloting trim bit costs $8 to $10, which is about half of what a ball-bearing-guided trimming bit costs. Ball-bearing-guided bits greatly reduce the risk of marring and can be used without a lubricant. The bearings do wear out, so you should replace them as soon as they show signs that they're not spinning freely. It's also important to keep them clean of built-up glue. Ball-bearing-guided trim bits are available in either a flush-trim or bevel-trim profile. The bevel profile (shown here) is used when you want to ease the edge to make it friendlier to the touch and reduce its chance of chipping when bumped. Ball-bearing-guided trim bits cost $12 to $24 each.# 3. Mar-Proof Routing
Use a ball-bearing guide attachment when you want to totally eliminate the chance of marring the finished surface or when you want to leave an overhang on the part that you are trimming. A nonpiloted trim bit is used with this guide. The bit is a combination flush and bevel cut. You can trim straight or curved surfaces with this setup.


4. Get a Super-Straight Cut
Use a straight guide when trimming against the substrate material. The straight guide bridges the small voids or gaps common in particleboard and plywood. The result is a straighter edge on the p-lam. This is important when another p-lam piece will be laminated to this edge. Straight edge guides do not work on curves or close in inside corners. A regular straight bit works fine with the straight guide.
5. Move Close into Corners

Click here to read the rest of the article from American Woodworker

Local Events

Philadelphia Flower Show 2018
Dates: 3/4/2018 – 3/11/2018
Location:
Pennsylvania Convention Center Philadelphia
View Details