Add Decorative Corner Splines Avenal CA
Decorative corner splines sure make an ordinary box look great. Butthey can be a bit dicey to cut on a tablesaw. Let your plate joinercome to the rescue. A simple jig holds the box and the joiner so youcan cut slots quickly with minimal setup hassles.
Ervins True Value Hardware
(559) 386-9740
735 Skyline Blvd
Avenal, CA
Bohnhoff Lumber Co, Inc.
323-263-9361
3411 E. 26th St.
Los Angeles, CA
Bohnhoff Lumber Co, Inc.
323-263-9361
3411 E. 26th St.
Los Angeles, CA 90058
Data Provided by:
The Home Depot
(626)443-2100
9700 Lower Azusa Road
El Monte, CA
The Home Depot
(626)443-2100
9700 Lower Azusa Road
El Monte, CA 91731
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-9:00pm
The Home Depot
(626)256-0580
1625 S Mountain Ave
Monrovia, CA
The Home Depot
(626)256-0580
1625 S Mountain Ave
Monrovia, CA 91016
Hours
Mon-Fri: 5:00am-11:00pm
Sat-Sun: 6:00am-11:00pm
The Home Depot
(714)685-9360
1855 N Tustin Ave
Orange, CA
The Home Depot
(714)685-9360
1855 N Tustin Ave
Orange, CA 92865
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm
Coalinga Hardware Inc
(559) 935-2961
109 N 5th St, corner of Fifth & Forrest
Coalinga, CA
The Home Depot
(650)755-0178303 E Lake Merced Blvd
Daly City, CA
The Home Depot
(650)755-0178
303 E Lake Merced Blvd
Daly City, CA 94015
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-9:00pm
The Home Depot
(805)737-0314
1701 East Ocean Avenue
Lompoc, CA
The Home Depot
(805)737-0314
1701 East Ocean Avenue
Lompoc, CA 93436
Hours
Mon-Sat: 7:00am-9:00pm
Sun: 8:00am-8:00pm
The Home Depot
(831)444-9814
1890 N Davis Road
Salinas, CA
The Home Depot
(831)444-9814
1890 N Davis Road
Salinas, CA 93907
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm
The Home Depot
(661)835-1133
4700 Gosford Road
Bakersfield, CA
The Home Depot
(661)835-1133
4700 Gosford Road
Bakersfield, CA 93313
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm
Data Provided by:
Add Decorative Corner Splines
Decorative corner splines sure make an ordinary box look great. Butthey can be a bit dicey to cut on a tablesaw. Let your plate joinercome to the rescue. A simple jig holds the box and the joiner so youcan cut slots quickly with minimal setup hassles. The jig is nothingmore than a piece of scrap plywood with two wood strips set at 90degrees to each other. A cradle fits around the plate joiner base andkeeps it from rocking on the box corner. The cradle is indexed to thejig with a couple dowels. Use spacer blocks to adjust the splinespacing. Plunge the joiner into the wood slowly to prevent tear-outwhere the blade exits the wood. With this box, you only need one spacerblock; just flip the box over to cut the upper slot.
Click here to read the rest of the article from American Woodworker
