American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » ยป

Align Bandsaw Wheels Ballwin MO

If you use a sharp blade designed for resawing,compensate for drift angle, set the proper tension and still get bad resawing results, there's only one other possibility:Your wheels need alignment. Pop the hood (well, the wheel covers) onyour saw and put a straightedge across the rim of both wheels (Photo1).

The Home Depot
(636)207-8875
13929 Manchester Rd
Ballwin, MO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Woodcraft - St. Louis/Maryland Heights
(314) 993-0413
2077 Congressional Drive
St. Louis, MO

Data Provided by:
The Home Depot
(314)647-6050
1603 S Hanley Rd
Brentwood, MO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(636)936-9494
3891 Mexico Rd
Saint Charles, MO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Rockler Woodworking and Hardware #19
(314) 209-1116
11977 St. Charles-Rock Rd.
St. Louis (Bridgeton), MO

Data Provided by:
The Home Depot
(636)536-0675
390 Thf Boulevard
Chesterfield, MO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(314)909-7771
10890 Sunset Hills Plaza
Saint Louis, MO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(636)922-1281
6190 Mid River Mall Dr
St Peter, MO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(314)733-1534
8901 Page Avenue
Overland, MO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(636)287-1111
3865 Vogel Rd
Arnold, MO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

Align Bandsaw Wheels

Align Bandsaw Wheels

Q. I've tried everything to get good resaw results on my bandsaw, but the blade still wanders. What gives?

A. If you use a sharp blade designed for resawing, compensate for drift angle, set the proper tension and still get bad resawing results, there's only one other possibility: Your wheels need alignment. Pop the hood (well, the wheel covers) onyour saw and put a straightedge across the rim of both wheels (Photo1). If there's a gap, your wheels are not operating in the same plane. Misaligned wheels are a problem for bandsaws with crowned wheels. If your saw is 16" or smaller, chances are it has crowned wheels. A crowned wheel has a slight hump where the blade rides. The crown is designed to force the blade toward the center of the wheel and aid intracking the blade. If the two crowned surfaces are not in the same plane, they pull against each other, robbing the saw of power and accuracy. Fortunately, the problem is easy to fix on most saws. First, measure the misalignment (Photo 2). Next, remove the blade and the wheel and apply the appropriate shim(s) (Photo 3). Most saws have thin washers behind each wheel. You may find removing the stock washer and replacing it with a thicker one is just the ticket. Reattach the wheel and give your saw a spin. Note: Some saws have an adjustable bottom wheel. Just loosen the setscrew and slide the bottom wheel in or out the appropriate amount.

PHOTO 1
Check the wheel alignment with your resaw blade mounted and tensioned. It may be necessary to adjust the tracking of the upper wheel to make the faces of both rims parallel.



PHOTO 2

Measure the gap with a ruler calibrated to at least 1/32" or with a dial caliper.



PHOTO 3:
Remove the wheel and add or subtract shims to eliminate the gap.


Click here to read the rest of the article from American Woodworker