American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » ยป

Align Bandsaw Wheels Boise ID

If you use a sharp blade designed for resawing,compensate for drift angle, set the proper tension and still get bad resawing results, there's only one other possibility:Your wheels need alignment. Pop the hood (well, the wheel covers) onyour saw and put a straightedge across the rim of both wheels (Photo1).

The Home Depot
(208)388-8500
3639 E Federal Way
Boise, ID
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Woodcraft - Boise, ID
(208) 338-1190
6883 West Overland Road
Boise, ID

Data Provided by:
The Home Depot
(208)887-9699
1100 S Progress
Meridian, ID
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(208)461-6476
2003 N Cassia St
Nampa, ID
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

KC Tool Supply/Boise
(203) 375-1313
5103 Irving St Boise, ID, 83706
Boise, ID
 
The Home Depot
(208) 388-8500
3639 S Federal Way
Boise, ID
 
The Home Depot
(208)375-1186
1200 Milwaukee Street
Boise, ID
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(208)939-7648
2808 E State Street
Eagle, ID
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Thriftway Home Center
(208) 336-7330
2050 Broadway Ave, 2 Blocks south of Garfield Elementary School
Boise, ID
 
Norco
(208) 336-1643
1125 West Amity Rd Boise, ID, 83705
Boise, ID
 
Data Provided by:

Align Bandsaw Wheels

Align Bandsaw Wheels

Q. I've tried everything to get good resaw results on my bandsaw, but the blade still wanders. What gives?

A. If you use a sharp blade designed for resawing, compensate for drift angle, set the proper tension and still get bad resawing results, there's only one other possibility: Your wheels need alignment. Pop the hood (well, the wheel covers) onyour saw and put a straightedge across the rim of both wheels (Photo1). If there's a gap, your wheels are not operating in the same plane. Misaligned wheels are a problem for bandsaws with crowned wheels. If your saw is 16" or smaller, chances are it has crowned wheels. A crowned wheel has a slight hump where the blade rides. The crown is designed to force the blade toward the center of the wheel and aid intracking the blade. If the two crowned surfaces are not in the same plane, they pull against each other, robbing the saw of power and accuracy. Fortunately, the problem is easy to fix on most saws. First, measure the misalignment (Photo 2). Next, remove the blade and the wheel and apply the appropriate shim(s) (Photo 3). Most saws have thin washers behind each wheel. You may find removing the stock washer and replacing it with a thicker one is just the ticket. Reattach the wheel and give your saw a spin. Note: Some saws have an adjustable bottom wheel. Just loosen the setscrew and slide the bottom wheel in or out the appropriate amount.

PHOTO 1
Check the wheel alignment with your resaw blade mounted and tensioned. It may be necessary to adjust the tracking of the upper wheel to make the faces of both rims parallel.



PHOTO 2

Measure the gap with a ruler calibrated to at least 1/32" or with a dial caliper.



PHOTO 3:
Remove the wheel and add or subtract shims to eliminate the gap.


Click here to read the rest of the article from American Woodworker