American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Align Bandsaw Wheels East Greenwich RI

If you use a sharp blade designed for resawing,compensate for drift angle, set the proper tension and still get bad resawing results, there's only one other possibility:Your wheels need alignment. Pop the hood (well, the wheel covers) onyour saw and put a straightedge across the rim of both wheels (Photo1).

Woodcraft - Providence, RI
(401) 886-1175
1000 Division Street
East Greenwich, RI

Data Provided by:
The Home Depot
(401)823-5173
700 Centre Of N E Blvd
Coventry, RI
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-7:00pm

The Home Depot
(401)845-5092
878 W Main Road
Middletown, RI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Wickford Lumber Co True Value
(401) 295-8866
434 Tower Hill Road
North Kingstown, RI
 
S&t True Value Hardware
(401) 397-6300
2300 Nooseneck Hill Rd
Coventry, RI
 
The Home Depot
(401)295-1184
1255 Ten Rod Road
North Kingstown, RI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Liberty Cedar, Inc.
(401) 789-6626
325 Liberty Lane
West Kingston, RI

Data Provided by:
St. Angelo Hardwoods, Inc. - Genuine Asian Teak Specialist
(401) 624-3900
490 Eagleville Road
Tiverton, RI

Data Provided by:
Lowe's
(401) 267-6330
1530 Davisville Road
North Kingstown, RI
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Lowe's
(401) 822-6300
510 Quaker Lane
Warwick, RI
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Data Provided by:

Align Bandsaw Wheels

Align Bandsaw Wheels

Q. I've tried everything to get good resaw results on my bandsaw, but the blade still wanders. What gives?

A. If you use a sharp blade designed for resawing, compensate for drift angle, set the proper tension and still get bad resawing results, there's only one other possibility: Your wheels need alignment. Pop the hood (well, the wheel covers) onyour saw and put a straightedge across the rim of both wheels (Photo1). If there's a gap, your wheels are not operating in the same plane. Misaligned wheels are a problem for bandsaws with crowned wheels. If your saw is 16" or smaller, chances are it has crowned wheels. A crowned wheel has a slight hump where the blade rides. The crown is designed to force the blade toward the center of the wheel and aid intracking the blade. If the two crowned surfaces are not in the same plane, they pull against each other, robbing the saw of power and accuracy. Fortunately, the problem is easy to fix on most saws. First, measure the misalignment (Photo 2). Next, remove the blade and the wheel and apply the appropriate shim(s) (Photo 3). Most saws have thin washers behind each wheel. You may find removing the stock washer and replacing it with a thicker one is just the ticket. Reattach the wheel and give your saw a spin. Note: Some saws have an adjustable bottom wheel. Just loosen the setscrew and slide the bottom wheel in or out the appropriate amount.

PHOTO 1
Check the wheel alignment with your resaw blade mounted and tensioned. It may be necessary to adjust the tracking of the upper wheel to make the faces of both rims parallel.



PHOTO 2

Measure the gap with a ruler calibrated to at least 1/32" or with a dial caliper.



PHOTO 3:
Remove the wheel and add or subtract shims to eliminate the gap.


Click here to read the rest of the article from American Woodworker