American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Align Bandsaw Wheels Evansville IN

If you use a sharp blade designed for resawing,compensate for drift angle, set the proper tension and still get bad resawing results, there's only one other possibility:Your wheels need alignment. Pop the hood (well, the wheel covers) onyour saw and put a straightedge across the rim of both wheels (Photo1).

Woodcraft - Evansville, IN
(812) 479-9663
Eastland Place Shopping Center
Evansville, IN

Data Provided by:
The Home Depot
(812)471-1132
333 N Burkhardt Rd
Evansville, IN
Hours
Mon-Thur: 6:00am-9:00pm
Fri-Sat: 6:00am-10:00pm
Sun: 8:00am-7:00pm

Ryan's Ace Hdw & Rental
(812) 402-1223
4530 N 1st Ave
Evansville, IN
 
LOWE'S OF E. EVANSVILLE, IND.
812 475-9655
6716 OAK GROVE ROAD EVANSVILLE, IN, 47715
Evansville, IN
 
LOWE'S OF W. EVANSVILLE, IND.
812 424-7605
103 SOUTH RED BANK ROAD EVANSVILLE, IN, 47712
Evansville, IN
 
The Home Depot
(812)423-6710
5230 Pearl Drive
Evansville, IN
Hours
Mon-Thur: 6:00am-9:00pm
Fri-Sat: 6:00am-10:00pm
Sun: 8:00am-7:00pm

Fastenal- Evansville
812-867-5369
8501 Baumgart Rd Evansville, IN, 47725
Evansville, IN
 
Fastenal- Evansville
812-464-5493
1401 Virginia Ave Evansville, IN, 47711
Evansville, IN
 
Lowe's
(812) 475-9655
6716 Oak Grove Road
Evansville, IN
Hours
M-SA 6 am - 10 pm
SU 8 am - 7 pm

Washington Sq
(812) 473-8200
1100 S Green River Rd
Evansville, IN
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18

Data Provided by:

Align Bandsaw Wheels

Align Bandsaw Wheels

Q. I've tried everything to get good resaw results on my bandsaw, but the blade still wanders. What gives?

A. If you use a sharp blade designed for resawing, compensate for drift angle, set the proper tension and still get bad resawing results, there's only one other possibility: Your wheels need alignment. Pop the hood (well, the wheel covers) onyour saw and put a straightedge across the rim of both wheels (Photo1). If there's a gap, your wheels are not operating in the same plane. Misaligned wheels are a problem for bandsaws with crowned wheels. If your saw is 16" or smaller, chances are it has crowned wheels. A crowned wheel has a slight hump where the blade rides. The crown is designed to force the blade toward the center of the wheel and aid intracking the blade. If the two crowned surfaces are not in the same plane, they pull against each other, robbing the saw of power and accuracy. Fortunately, the problem is easy to fix on most saws. First, measure the misalignment (Photo 2). Next, remove the blade and the wheel and apply the appropriate shim(s) (Photo 3). Most saws have thin washers behind each wheel. You may find removing the stock washer and replacing it with a thicker one is just the ticket. Reattach the wheel and give your saw a spin. Note: Some saws have an adjustable bottom wheel. Just loosen the setscrew and slide the bottom wheel in or out the appropriate amount.

PHOTO 1
Check the wheel alignment with your resaw blade mounted and tensioned. It may be necessary to adjust the tracking of the upper wheel to make the faces of both rims parallel.



PHOTO 2

Measure the gap with a ruler calibrated to at least 1/32" or with a dial caliper.



PHOTO 3:
Remove the wheel and add or subtract shims to eliminate the gap.


Click here to read the rest of the article from American Woodworker