American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » ยป

Align Bandsaw Wheels Newberg OR

If you use a sharp blade designed for resawing,compensate for drift angle, set the proper tension and still get bad resawing results, there's only one other possibility:Your wheels need alignment. Pop the hood (well, the wheel covers) onyour saw and put a straightedge across the rim of both wheels (Photo1).

The Home Depot
(503)925-8447
20260 SW Pacific Hwy
Sherwood, OR
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Woodcraft - Portland, OR
(503) 684-1428
12020 SW Main Street
Tigard, OR

Data Provided by:
Rockler Woodworking and Hardware #17
(503) 672-7266
Beaverton Town Square Mall
Beaverton (Portland), OR

Data Provided by:
R and K Woodworking Rare and Exotic Wood
(503) 330-1155
1913 D Street
Forest Grove, OR

Data Provided by:
Columbia Riverwood
(503) 224-9924
1017 SW Morrison St P.O. Box 10461
Portland, OR

Data Provided by:
The Home Depot
(503)693-9090
1950 SE Minter Bridge Rd
Hillsboro, OR
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(503)639-3500
14800 SW Sequoia Parkway
Tigard, OR
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(503)469-4242
4401 Southwest 110th Ave
Beaverton, OR
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(503)646-1525
13700 NW Science Pk Dr
Portland, OR
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Gilmer Wood Company
(503) 274-1271
2211 NW Saint Helens Road
Portland, OR

Data Provided by:
Data Provided by:

Align Bandsaw Wheels

Align Bandsaw Wheels

Q. I've tried everything to get good resaw results on my bandsaw, but the blade still wanders. What gives?

A. If you use a sharp blade designed for resawing, compensate for drift angle, set the proper tension and still get bad resawing results, there's only one other possibility: Your wheels need alignment. Pop the hood (well, the wheel covers) onyour saw and put a straightedge across the rim of both wheels (Photo1). If there's a gap, your wheels are not operating in the same plane. Misaligned wheels are a problem for bandsaws with crowned wheels. If your saw is 16" or smaller, chances are it has crowned wheels. A crowned wheel has a slight hump where the blade rides. The crown is designed to force the blade toward the center of the wheel and aid intracking the blade. If the two crowned surfaces are not in the same plane, they pull against each other, robbing the saw of power and accuracy. Fortunately, the problem is easy to fix on most saws. First, measure the misalignment (Photo 2). Next, remove the blade and the wheel and apply the appropriate shim(s) (Photo 3). Most saws have thin washers behind each wheel. You may find removing the stock washer and replacing it with a thicker one is just the ticket. Reattach the wheel and give your saw a spin. Note: Some saws have an adjustable bottom wheel. Just loosen the setscrew and slide the bottom wheel in or out the appropriate amount.

PHOTO 1
Check the wheel alignment with your resaw blade mounted and tensioned. It may be necessary to adjust the tracking of the upper wheel to make the faces of both rims parallel.



PHOTO 2

Measure the gap with a ruler calibrated to at least 1/32" or with a dial caliper.



PHOTO 3:
Remove the wheel and add or subtract shims to eliminate the gap.


Click here to read the rest of the article from American Woodworker