American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Align Bandsaw Wheels Park Hills MO

If you use a sharp blade designed for resawing,compensate for drift angle, set the proper tension and still get bad resawing results, there's only one other possibility:Your wheels need alignment. Pop the hood (well, the wheel covers) onyour saw and put a straightedge across the rim of both wheels (Photo1).

Holekamp Do it center
(573) 358-3371
317 N Division
Bonne Terre, MO
 
Maple Valley Ctr
(573) 760-1502
738 Market St
Farmington, MO
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:11-16
Store Features
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:11-16

Lowe's
(573) 701-8200
625 West Karsch Boulevard
Farmington, MO
Hours
M-SA 7 am - 9 pm
SU 9 am - 7 pm

Fastenal- Farmington
573-756-0368
424 N. Washington St Farmington, MO, 63640
Farmington, MO
 
Boyer Do it Best Lumber
(573) 438-5461
208 West High Street
Potosi, MO
 
LOWE'S OF FARMINGTON, MO
573 701-8200
625 WEST KARSCH BOULEVARD FARMINGTON, MO, 63640
Farmington, MO
 
Farmington Building Supply Co.
(573) 756-5705
306 East Karsch Blvd.
Farmington, MO
 
Plummer's Hardware
(573) 756-6001
101 E Liberty
Farmington, MO
 
ABC Supply Co.,Inc/Farmington
573-431-7076
190 Busenbark Place Farmington, MO, 63640
Farmington, MO
 
Dickey Bub True Value
(573) 436-1177
708 High Street E
Potosi, MO
 

Align Bandsaw Wheels

Align Bandsaw Wheels

Q. I've tried everything to get good resaw results on my bandsaw, but the blade still wanders. What gives?

A. If you use a sharp blade designed for resawing, compensate for drift angle, set the proper tension and still get bad resawing results, there's only one other possibility: Your wheels need alignment. Pop the hood (well, the wheel covers) onyour saw and put a straightedge across the rim of both wheels (Photo1). If there's a gap, your wheels are not operating in the same plane. Misaligned wheels are a problem for bandsaws with crowned wheels. If your saw is 16" or smaller, chances are it has crowned wheels. A crowned wheel has a slight hump where the blade rides. The crown is designed to force the blade toward the center of the wheel and aid intracking the blade. If the two crowned surfaces are not in the same plane, they pull against each other, robbing the saw of power and accuracy. Fortunately, the problem is easy to fix on most saws. First, measure the misalignment (Photo 2). Next, remove the blade and the wheel and apply the appropriate shim(s) (Photo 3). Most saws have thin washers behind each wheel. You may find removing the stock washer and replacing it with a thicker one is just the ticket. Reattach the wheel and give your saw a spin. Note: Some saws have an adjustable bottom wheel. Just loosen the setscrew and slide the bottom wheel in or out the appropriate amount.

PHOTO 1
Check the wheel alignment with your resaw blade mounted and tensioned. It may be necessary to adjust the tracking of the upper wheel to make the faces of both rims parallel.



PHOTO 2

Measure the gap with a ruler calibrated to at least 1/32" or with a dial caliper.



PHOTO 3:
Remove the wheel and add or subtract shims to eliminate the gap.


Click here to read the rest of the article from American Woodworker