American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Arts and Crafts Table Lamp Aberdeen SD

Our table lamp is reminiscent of the Prairie style of design, with lines that Frank Lloyd Wright might favor. In spite of its complex-looking shade, this elegant lamp is within reach of any intermediate woodworker.

Campbell's Building Supply
(605) 225-1575
1523 6th Ave S W
Aberdeen, SD
 
Aberdeen - Auth Hometown
(605) 226-2500
3315 6Th Ave Se Ste 8
Aberdeen, SD
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-18
Sun:12-17
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-18
Sun:12-17

Homestead Building Supplies
(605) 439-3161
Highway 10 West
Leola, SD
 
Lowe's of Brookings
605-696-2730
812 25th Ave Brookings, SD, 57006
Brookings, SD
 
Fullerton Lumber Co 938
(605) 665-9651
2409 Broadway Ave
Yankton, SD
 
Fastenal- Aberdeen
605-226-8238
6 Nth Dakota Street Suite 100 Aberdeen, SD, 57401
Aberdeen, SD
 
Kmart 7023 / Cross Merch
(605) 229-5510
1815 6Th Ave Se
Aberdeen, SD
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :0-0 and for Sat:0-0
Sun:0-0
Store Features
Monday To Friday Working Hours is :0-0 and for Sat:0-0
Sun:0-0

The Home Depot
(605)361-7439
2523 S Louise Ave
Sioux Falls, SD
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

Sioux Falls - D
(605) 339-1400
3020 W 12Th St
Sious Falls, SD
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

Country Pride Coop
(605) 259-3141
Highway 83
White River, SD
 

Arts and Crafts Table Lamp

Arts and Crafts Table Lamp

Sure-fire steps simplify the intricate shade joinery.

by Jon Stumbras

Our table lamp is reminiscent of the Prairie style of design, with lines that Frank Lloyd Wright might favor. In spite of its complex-looking shade, this elegant lamp is within reach of any intermediate woodworker. We’ve figured out a straightforward system that tames all those nasty angles and guarantees good results. The wiring is also simple, even if you haven’t done much electrical work. All the parts are readily available through the mail or at a lighting store. You may find that the hardest part is selecting the stained glass. There is a bewildering array of colors and textures to choose from, but that’s part of the fun.

Build the Shade Frame

The shade is made of four identical frames. Use a stop block for all the cuts. 

1. Mill the 4/4 mahogany to thickness and rip the boards into 1-in. widths. Rough-cut three 12-in. pieces and one 18-in. piece for each of the four frames (K, L, M). Cut enough parts to build an extra frame as a precaution and for setup purposes.

2. Attach a long auxiliary fence to your tablesaw’s miter gauge. We added an acrylic guard just as a reminder of where not to put one’s fingers. 

3. Make a setup block for setting your miter gauge angles by cutting a 38-degree angle on one end and a 26-degree angle on the other one. Use an accurate miter saw to cut the block. 

4. Set the miter gauge to cut at 38 degrees (Photo 1). Miter both ends of the frame sides (K) and frame bottoms (M) to final dimensions. Miter just the left edge of the frame top (L). All these cuts can be made using one miter fence setting. 

5. Cut the half-lap joint on the mitered end of each piece (Photo 2; Fig. B, below). Use scrap wood to set the blade height and a stop block for each cut. You will need to rotate the miter gauge 38 degrees right and left of center to accomplish all the angles. 

6. Dry-fit all the pieces together and mark the position of the half-lap on the right side of the frame top (Photo 3). Then cut the rest of the top half-laps.

7. Glue each frame assembly together with small C-clamps. When the glue has set, cut off the waste on the top.

Rabbet for the Glass

8. Make a template out of 1/4-in. plywood to cut rabbets in each frame. Simply place a shade frame on the plywood, trace the interior and mark lines 1/4 in. to the outside of the tracing lines. Cut to this line with a jigsaw. Keep the template 3 in. wide to support the router. 

9. Rout the rabbet with a 1/4-in. straight bit and guide bushing (Photo 4; Fig. C, below). Take several passes of to get the rabbet to full depth. Clean up the corners of the rabbet using a chisel.

Cut the Compound Miters

10. Use the setup block to set the tablesaw miter fence to cut at 38 degrees and angle the blade to 26 degrees. 

11. Place a frame, face side up, with the bottom against the fence. Cut the co...

Click here to read the rest of the article from American Woodworker