American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Arts and Crafts Table Lamp Traverse City MI

Our table lamp is reminiscent of the Prairie style of design, with lines that Frank Lloyd Wright might favor. In spite of its complex-looking shade, this elegant lamp is within reach of any intermediate woodworker.

Rare Earth Hardwoods
(231) 946-0043
6778 East Traverse Hwy
Traverse, MI

Data Provided by:
Cherryland Mall
(231) 933-5000
1212 S Airport Rd W
Traverse City, MI
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:9.5-21
Tue:9.5-21
Wed:9.5-21
Thu:9.5-21
Fri:9.5-21
Sat:9-21
Sun:11-18
Store Features
Mon:9.5-21
Tue:9.5-21
Wed:9.5-21
Thu:9.5-21
Fri:9.5-21
Sat:9-21
Sun:11-18

Cummins Bridgeway
231-947-5824
863 South Airport Traverse City, MI, 49686
Traverse City, MI
 
Brown Lumber
(231) 947-1400
1701 Airport Rd Traverse City, MI, 49686
Traverse City, MI
 
Gill-Roy's Hometown Hardware
(231) 929-8160
2701 Zimmerman
Traverse City, MI
 
The Home Depot
(231)922-9440
2522 Crossing Circle
Traverse City, MI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Kmart 3009 / Cross Merch
(231) 941-0600
1712 S Garfield Ave
Traverse City, MI
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

De Weese Do it Best Hardware
(231) 947-7670
1029 Carver
Traverse City, MI
 
Fastenal- Traverse City
231-947-7665
2425 Sybrandt Ave Traverse City, MI, 49684
Traverse City, MI
 
ABC Supply Co.,Inc/Traverse City
231-941-4428
10660 E Carter Rd Traverse City, MI, 49684
Traverse City, MI
 
Data Provided by:

Arts and Crafts Table Lamp

Arts and Crafts Table Lamp

Sure-fire steps simplify the intricate shade joinery.

by Jon Stumbras

Our table lamp is reminiscent of the Prairie style of design, with lines that Frank Lloyd Wright might favor. In spite of its complex-looking shade, this elegant lamp is within reach of any intermediate woodworker. We’ve figured out a straightforward system that tames all those nasty angles and guarantees good results. The wiring is also simple, even if you haven’t done much electrical work. All the parts are readily available through the mail or at a lighting store. You may find that the hardest part is selecting the stained glass. There is a bewildering array of colors and textures to choose from, but that’s part of the fun.

Build the Shade Frame

The shade is made of four identical frames. Use a stop block for all the cuts. 

1. Mill the 4/4 mahogany to thickness and rip the boards into 1-in. widths. Rough-cut three 12-in. pieces and one 18-in. piece for each of the four frames (K, L, M). Cut enough parts to build an extra frame as a precaution and for setup purposes.

2. Attach a long auxiliary fence to your tablesaw’s miter gauge. We added an acrylic guard just as a reminder of where not to put one’s fingers. 

3. Make a setup block for setting your miter gauge angles by cutting a 38-degree angle on one end and a 26-degree angle on the other one. Use an accurate miter saw to cut the block. 

4. Set the miter gauge to cut at 38 degrees (Photo 1). Miter both ends of the frame sides (K) and frame bottoms (M) to final dimensions. Miter just the left edge of the frame top (L). All these cuts can be made using one miter fence setting. 

5. Cut the half-lap joint on the mitered end of each piece (Photo 2; Fig. B, below). Use scrap wood to set the blade height and a stop block for each cut. You will need to rotate the miter gauge 38 degrees right and left of center to accomplish all the angles. 

6. Dry-fit all the pieces together and mark the position of the half-lap on the right side of the frame top (Photo 3). Then cut the rest of the top half-laps.

7. Glue each frame assembly together with small C-clamps. When the glue has set, cut off the waste on the top.

Rabbet for the Glass

8. Make a template out of 1/4-in. plywood to cut rabbets in each frame. Simply place a shade frame on the plywood, trace the interior and mark lines 1/4 in. to the outside of the tracing lines. Cut to this line with a jigsaw. Keep the template 3 in. wide to support the router. 

9. Rout the rabbet with a 1/4-in. straight bit and guide bushing (Photo 4; Fig. C, below). Take several passes of to get the rabbet to full depth. Clean up the corners of the rabbet using a chisel.

Cut the Compound Miters

10. Use the setup block to set the tablesaw miter fence to cut at 38 degrees and angle the blade to 26 degrees. 

11. Place a frame, face side up, with the bottom against the fence. Cut the co...

Click here to read the rest of the article from American Woodworker