American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » ยป

Benchtop Mortisers Canby OR

Traditionally, mortisers used fast-speed, 3,450 rpm motors, but now slow-speed machines are also on the market. Three of the machines we tested have 1,725-rpm motors. Read on to learn more.

The Home Depot
(503)723-3181
2002 Washington Street
Oregon City, OR
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(503)639-3500
14800 SW Sequoia Parkway
Tigard, OR
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(503)469-4242
4401 Southwest 110th Ave
Beaverton, OR
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Woodcrafters
(800) 777-3709
212 NE 6th Ave
Portland, OR

Data Provided by:
Wilco Farm Stores - Canby
(503) 266-2213
195 S Hazel Dell Way
Canby, OR
 
The Home Depot
(503)925-8447
20260 SW Pacific Hwy
Sherwood, OR
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Woodcraft - Portland, OR
(503) 684-1428
12020 SW Main Street
Tigard, OR

Data Provided by:
Rockler Woodworking and Hardware #17
(503) 672-7266
Beaverton Town Square Mall
Beaverton (Portland), OR

Data Provided by:
The Home Depot
(503)261-8543
10120 SE Washington St
Portland, OR
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Canby Ace Hardware
(503) 263-2500
1061 SW 1st Ave, Safeway Center on 99E
Canby, OR
 
Data Provided by:

Benchtop Mortisers

Benchtop Mortisers

For $250 and half an hour's worth of simple improvements, you can cut precise mortises all day.

Mortising machines first answered the prayers of mortise-cutting woodworkers over 120 years ago. Today you can buy a miniaturized descendant of those old-timers. Though they're not the only powered option you have for mortising these days, their square mortises are the perfect match for tablesawn tenons. We tested eight benchtop machines designed to cut mortises up to 1/2-in. wide. They're similar in size and capacity, and all but one sell for less than $250. They all use the same specialized chisels and drill bits. The machines are easy to set up and ready to cut mortises within 20 minutes. After our own testing, we invited a group of professional and amateur woodworkers to try out the machines as well. All together, we cut hundreds of mortises with each machine, using 1/4-in. to 1/2-in. chisel sets, in mahogany, red oak and maple.

Benchtop Mortisers

It's Okay to buy Cheap Bits
For testing, each machine was outfitted with new chisel sets from the same manufacturer. We tried sets from British, American, Austrian and Japanese manufacturers before deciding to use the cheapest ones, which are made in Taiwan. You can spend a lot of money on chisel sets, but we think these inexpensive ones (usually less than $20), are a good buy. Out of the box, they needed the least amount of sharpening. They cut clean mortises and we found them easy to resharpen. Besides, accidents happen, bits get ruined and it's less traumatic to replace a cheap set. Taiwanese sets are usually available from suppliers who sell benchtop mortisers.

A HOLLOW CHISEL with an auger bit inside is the secret to machines that cut aquare mortises. First the auger roughs out the mortise by drilling a hole and clearing the chips. To square the corners, you have to force the chisel through the wood. This can take a lot of force-a square 1/2-in. mortise chisel has a 2-in. cutting edge. That's why mortising machines take muscle to operate.

The Major Difference Between Machines Is Motor Speed
Traditionally, mortisers used fast-speed, 3,450 rpm motors, but now slow-speed machines are also on the market. Three of the machines we tested have 1,725-rpm motors. Why the change? Manufacturers we talked to say slower speeds increase the life of the chisel sets. We think that's one reason slow-speed machines are less stressful to use. You don't have to worry about overheating the tooling. They're also quieter and rarely cause smoke. However, they don't cut mortises as easily as fast-speed machines. At a comfortable feed rate, we found cutting 1/2-in. mortises takes 5 to 10 foot/pounds more effort. Fast or slow speed? You have a choice between cutting ease and ease of mind.

Tune UP THE AUGER before you use it. With a small file, remove leftover machining burrs from the inside adge of it's scoring spur and the a...

Click here to read the rest of the article from American Woodworker