American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Cathedral Style Cabinet Doors Pacific MO

Cathedral raised-panel doors are beautiful, but they can beintimidating to make. After many years of teaching students how to makethese doors, I've got a trick or two up my sleeve to simplify theprocess and remove some of the fear factor. Here's a tried-and-truerecipe to help you safely and successfully make beautiful doors.

The Home Depot
(636)536-0675
390 Thf Boulevard
Chesterfield, MO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(636)922-1281
6190 Mid River Mall Dr
St Peter, MO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Pacific Do it Best Lumber
(636) 271-4863
625 S Fourth St
Pacific, MO
 
Dickey Bub True Value
(636) 587-3900
100 Hilltop Village Center Drive
Eureka, MO
 
LOWE'S OF CHESTERFIELD, MO.
636 728-0163
290 THF BLVD CHESTERFIELD, MO, 63005
Chesterfield, MO
 
The Home Depot
(636)207-8875
13929 Manchester Rd
Ballwin, MO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(314)909-7771
10890 Sunset Hills Plaza
Saint Louis, MO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Gray Summit Do it Best
(636) 451-2707
2625 Highway 100
Gray Summit, MO
 
Lowe's
(636) 728-0163
290 T.H.F. Blvd
Chesterfield, MO
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

High Ridge - Sears Hardware Stores
(636) 376-4330
40 Dillon Plaza Dr
High Ridge, MO
Store Hours
Hardware Stores
Store Type
Hardware Stores
Hours
Mon:8-21
Tue:8-21
Wed:8-21
Thu:8-21
Fri:8-21
Sat:8-21
Sun:9-18
Store Features
Mon:8-21
Tue:8-21
Wed:8-21
Thu:8-21
Fri:8-21
Sat:8-21
Sun:9-18

Cathedral Style Cabinet Doors

Cathedral Style Cabinet Doors



Cathedral raised-panel doors are beautiful, but they can be intimidating to make. After many years of teaching students how to make these doors, I've got a trick or two up my sleeve to simplify the process and remove some of the fear factor. Here's a tried-and-true recipe to help you safely and successfully make beautiful doors.

There are a few specialized tools you must have to make cathedral doors. Start with a suitable router table. It should be equipped with a2-hp or higher variable-speed router that accepts 1/2-in.-shank router bits. You'll also need a band saw or jigsaw for cutting the curves and a set of door-making router bits. The bits and a template set will set you back nearly $400, but they are a big part of what makes this technique airtight. The good news is the router bits are not specific to cathedral-top doors; they can be used to make any frame-and-panel door.


You'll need a two-piece matched rail-and-stile set (about $135) to make the frame. It's easier to get good results with a two-piece set than with a one-piece reversible bit. With a two-piece set, you feed all the pieces face down. Reversible bits use one arbor with removable cutters. Some parts are machined face up, others face down. This often results in poor alignment between rails and stiles. Plus, it's a hassle to have to change cutters on the arbor. Bits with a 1/2-in. shank will produce less chatter and a smoother cut than those with 1/4-in. shank.



The end-grain cutter is used only on the rail ends and produces the tongue and the mating profile to the molded edge. The depth of cut is controlled by a bearing that rides against the tongue. Mark a number 1on the end of the shaft with a permanent marker, because it's the first cutter you'll use.

The long-grain cutter is used on the inside edge of all the frame pieces. It makes the groove for both the panel and the tongue on the end of the rails. It also forms the molded edge you see around the inside of the frame. Label this bit with the number 2.



Usea back-cutting panel raiser (about $150) to make the panel. The main cutter cuts a broad profile in the face of the panel. At the same time, the back cutter sweeps material off the back of the panel to leave a perfectly sized tongue for the  groove in the frame. Our favorite bits come with two bearings: The large-diameter bearing is used for the first pass and the small bearing for the final pass.

Make the Frame
First, cut all the frame pieces (see “Sizing a Door,”). For a good-looking, stable door, make the frame from straight-grained wood. Next, on your router table, set up the end-grain cutter for machining the rail ends. Cutting end grain before long grain helps prevent blow-out on the rails. Here's a memory device for you: Machine the Rails before the Stiles, because R comes before S in the alphabet. Mark the back of all the frame pieces. They get ...

Click here to read the rest of the article from American Woodworker