American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Coping with Inside Miters Bridgeton NJ

Cabinet-makers have used this joint to create great-looking inside corners for centuries. The technique involves cutting a profile on the end of the molding that fits like a puzzle piece against the adjoining piece (see above).

The Home Depot
(856)293-1155
3849 South Delsea Dr
Vineland, NJ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

H & R Hardware & Garden Ctr
(856) 451-1090
8 - 16 Centerton Road
Bridgeton, NJ
 
Lowe's
(856) 327-7010
113 Bluebird Lane
Millville, NJ
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Hankins Hh & Bro Hardware
(856) 451-1215
12 Broad St W
Bridgeton, NJ

Data Provided by:
Alloway Village Hardware
(856) 935-6888
43 N Greenwich St
Alloway, NJ

Data Provided by:
H. H. Hankins Do it Best
(856) 451-1212
12 West Broad St
Bridgeton, NJ
 
Vineland - B
(856) 692-2000
8 W Landis Ave
Vineland, NJ
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:9.5-21
Tue:9.5-21
Wed:9.5-21
Thu:9.5-21
Fri:9.5-21
Sat:9.5-21
Sun:11-18
Store Features
Mon:9.5-21
Tue:9.5-21
Wed:9.5-21
Thu:9.5-21
Fri:9.5-21
Sat:9.5-21
Sun:11-18

Warren's Do it Best
(856) 478-2600
110 Bridgeton Pike
Mullica Hill, NJ
 
Bostwick True Value Hardware
(800) 642-7392
Elmer & Center St
Elmer, NJ

Data Provided by:
I S Smick Lumber
(800) 642-7392
Rte 49 & Cottage Ave
Quinton, NJ

Data Provided by:
Data Provided by:

Coping with Inside Miters

Coping with Inside Miters

A time honored technique for applying molding to inside corners.

by Dave Munkittrick

The best technique for applying molding on an inside corner is called a coped joint. Cabinet-makers have used this joint to create great-looking inside corners for centuries. The technique involves cutting a profile on the end of the molding that fits like a puzzle piece against the adjoining piece (see above). 

To create the profile, cut a 45-degree miter on the end of the molding (Photo 1), just as you would if you were going to miter the joints. Then, use a coping saw with a fine-toothed blade to cut out the profile (Photo 2). Only the simplest moldings will allow you to complete the joint with one long cut. For abrupt direction changes, you’ll need to back out of the cut and approach it from a different angle. Use files to clean up the profiled edge and fine-tune the fit (Photo 3). 

Photo 1: Make an inside 45-degree cut to create a profiled edge. The molding should be held upside down on the saw. A stop block clamped to the saw holds the molding in place.

Photo 2: Cut the profile with a coping saw following the profile line created by the miter cut. Angle the saw back about 30 degrees as you cut along the profile to remove more wood from the back of the molding. 

Photo 3: Files fine-tune the cut. Choose a file that matches the particular profile. File and test-fit until the joint is tight.

This story originally appeared in  American Woodworker September 2005, issue #116.

Source information may have changed since the original publication date.

September 2005, issue #116

Purchase this back issue.

Click here to read the rest of the article from American Woodworker

Local Events

Philadelphia Flower Show 2018
Dates: 3/4/2018 – 3/11/2018
Location:
Pennsylvania Convention Center Philadelphia
View Details