American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Coping with Inside Miters De Soto MO

Cabinet-makers have used this joint to create great-looking inside corners for centuries. The technique involves cutting a profile on the end of the molding that fits like a puzzle piece against the adjoining piece (see above).

The Home Depot
(636)937-9601
1131 W Gannon
Festus, MO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Dep Builders Supply/dep Heating & Cooling
(636) 337-3381
12561 Hwy 21
De Soto, MO
 
Festus Do it center
(636) 937-9663
1198 Shapiro Dr
Festus, MO
 
Lowe's
(636) 933-3320
1111 Bradley Street
Festus, MO
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Crystal City - Dlr In Kmart
(636) 933-7011
155 Twin City Mall
Crystal City, MO
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-22
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-22

Hopson Lumber Company
(636) 586-3311
918 South Main Street
De Soto, MO
 
Hamel & Rowe Inc
(636) 586-3230
210 N Main St
De Soto, MO
 
LOWE'S OF FESTUS, MO
636 933-3320
1111 BRADLEY STREET FESTUS, MO, 63028
Festus, MO
 
Holekamp Do it center
(573) 358-3371
317 N Division
Bonne Terre, MO
 
ABC Supply Co.,Inc./Herculaneum
636-937-9150
1538 Industrial Dr Herculaneum, MO, 63048
Herculaneum, MO
 

Coping with Inside Miters

Coping with Inside Miters

A time honored technique for applying molding to inside corners.

by Dave Munkittrick

The best technique for applying molding on an inside corner is called a coped joint. Cabinet-makers have used this joint to create great-looking inside corners for centuries. The technique involves cutting a profile on the end of the molding that fits like a puzzle piece against the adjoining piece (see above). 

To create the profile, cut a 45-degree miter on the end of the molding (Photo 1), just as you would if you were going to miter the joints. Then, use a coping saw with a fine-toothed blade to cut out the profile (Photo 2). Only the simplest moldings will allow you to complete the joint with one long cut. For abrupt direction changes, you’ll need to back out of the cut and approach it from a different angle. Use files to clean up the profiled edge and fine-tune the fit (Photo 3). 

Photo 1: Make an inside 45-degree cut to create a profiled edge. The molding should be held upside down on the saw. A stop block clamped to the saw holds the molding in place.

Photo 2: Cut the profile with a coping saw following the profile line created by the miter cut. Angle the saw back about 30 degrees as you cut along the profile to remove more wood from the back of the molding. 

Photo 3: Files fine-tune the cut. Choose a file that matches the particular profile. File and test-fit until the joint is tight.

This story originally appeared in  American Woodworker September 2005, issue #116.

Source information may have changed since the original publication date.

September 2005, issue #116

Purchase this back issue.

Click here to read the rest of the article from American Woodworker