American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Coping with Inside Miters Fort Morgan CO

Cabinet-makers have used this joint to create great-looking inside corners for centuries. The technique involves cutting a profile on the end of the molding that fits like a puzzle piece against the adjoining piece (see above).

Fastenal- Ft. Morgan
970-867-4475
19873 US Highway 34 Ft. Morgan, CO, 80701
Ft. Morgan, CO
 
Murdoch's Ranch & Home Supply
(970) 542-1515
1207 W. Platte Avenue
Fort Morgan, CO
 
Bloedorn Lumber Building Mtrls
(970) 867-5646
130 State Street
Fort Morgan, CO
 
Country Do it Best Hardware
(970) 483-7312
218 Main St.
Wiggins, CO
 
The Home Depot
(303)697-6619
4277 S Eldridge Street
Morrison, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Ft Morgan - Auth Hometown
(970) 867-5200
1997 E Piatte Ave
Fort Morgan, CO
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:12.5-17.5
Store Features
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:12.5-17.5

Mr. D'S Ace Home Center
(970) 867-3303
1000 East Platte Avenue
Fort Morgan, CO
 
Farm & Home Hardware
(970) 842-2879
122 Custer St
Brush, CO
 
The Home Depot
(303)655-1686
2440 Buckley Road
Brighton, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(303)232-6303
6701 W Alameda Ave
Lakewood, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Coping with Inside Miters

Coping with Inside Miters

A time honored technique for applying molding to inside corners.

by Dave Munkittrick

The best technique for applying molding on an inside corner is called a coped joint. Cabinet-makers have used this joint to create great-looking inside corners for centuries. The technique involves cutting a profile on the end of the molding that fits like a puzzle piece against the adjoining piece (see above). 

To create the profile, cut a 45-degree miter on the end of the molding (Photo 1), just as you would if you were going to miter the joints. Then, use a coping saw with a fine-toothed blade to cut out the profile (Photo 2). Only the simplest moldings will allow you to complete the joint with one long cut. For abrupt direction changes, you’ll need to back out of the cut and approach it from a different angle. Use files to clean up the profiled edge and fine-tune the fit (Photo 3). 

Photo 1: Make an inside 45-degree cut to create a profiled edge. The molding should be held upside down on the saw. A stop block clamped to the saw holds the molding in place.

Photo 2: Cut the profile with a coping saw following the profile line created by the miter cut. Angle the saw back about 30 degrees as you cut along the profile to remove more wood from the back of the molding. 

Photo 3: Files fine-tune the cut. Choose a file that matches the particular profile. File and test-fit until the joint is tight.

This story originally appeared in  American Woodworker September 2005, issue #116.

Source information may have changed since the original publication date.

September 2005, issue #116

Purchase this back issue.

Click here to read the rest of the article from American Woodworker