American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Coping with Inside Miters Galax VA

Cabinet-makers have used this joint to create great-looking inside corners for centuries. The technique involves cutting a profile on the end of the molding that fits like a puzzle piece against the adjoining piece (see above).

Blevins Do it Best Building
(276) 236-8171
302 South Main Street
Galax, VA
 
Lowe's
(276) 238-3000
8417 Carrollton/Pike Road
Galax, VA
Hours
M-SA 7 am - 9 pm
SU 9 am - 7 pm

Blevins Do it Best Building
(336) 372-4000
652 North Main Street
Sparta, NC
 
Apache Forest Products L.L.C
(804) 744-7081
5104 W.Village Green Dr. Suite # 106
Midlothian, VA

Data Provided by:
The Home Depot
(757)548-8478
1400 Tintern Lane
Chesapeake, VA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Galax - Auth Hometown
(276) 238-8600
972 E Stuart Dr
Galax, VA
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-19
Tue:9-19
Wed:9-20
Thu:9-20
Fri:9-20
Sat:9-19
Sun:12-18
Store Features
Mon:9-19
Tue:9-19
Wed:9-20
Thu:9-20
Fri:9-20
Sat:9-19
Sun:12-18

LOWE'S OF GALAX, VA.
276 238-3000
8417 CARROLLTON/PIKE ROAD GALAX, VA, 24333
Galax, VA
 
Blevins Do it Best Building
(336) 363-2216
7258 Hwy 21 South
Glade Valley, NC
 
The Home Depot
(540)368-0515
1201 Gateway Blvd
Fredericksburg, VA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

C. P. Johnson Lumber
(540) 937-3059
21457 Bunisess Ct
Elkwood, VA

Data Provided by:
Data Provided by:

Coping with Inside Miters

Coping with Inside Miters

A time honored technique for applying molding to inside corners.

by Dave Munkittrick

The best technique for applying molding on an inside corner is called a coped joint. Cabinet-makers have used this joint to create great-looking inside corners for centuries. The technique involves cutting a profile on the end of the molding that fits like a puzzle piece against the adjoining piece (see above). 

To create the profile, cut a 45-degree miter on the end of the molding (Photo 1), just as you would if you were going to miter the joints. Then, use a coping saw with a fine-toothed blade to cut out the profile (Photo 2). Only the simplest moldings will allow you to complete the joint with one long cut. For abrupt direction changes, you’ll need to back out of the cut and approach it from a different angle. Use files to clean up the profiled edge and fine-tune the fit (Photo 3). 

Photo 1: Make an inside 45-degree cut to create a profiled edge. The molding should be held upside down on the saw. A stop block clamped to the saw holds the molding in place.

Photo 2: Cut the profile with a coping saw following the profile line created by the miter cut. Angle the saw back about 30 degrees as you cut along the profile to remove more wood from the back of the molding. 

Photo 3: Files fine-tune the cut. Choose a file that matches the particular profile. File and test-fit until the joint is tight.

This story originally appeared in  American Woodworker September 2005, issue #116.

Source information may have changed since the original publication date.

September 2005, issue #116

Purchase this back issue.

Click here to read the rest of the article from American Woodworker