American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Coping with Inside Miters Minot ND

Cabinet-makers have used this joint to create great-looking inside corners for centuries. The technique involves cutting a profile on the end of the molding that fits like a puzzle piece against the adjoining piece (see above).

ACME TOOLS- Minot
(701) 839-2263
700 20th Ave SE Minot, ND, 58701
Minot, ND
 
Fastenal- Minot
701-839-7566
700 20th Ave SW Minot, ND, 58701
Minot, ND
 
Enerbase
(701) 852-2501
215 Central Ave E
Minot, ND
 
Minot - D
(701) 852-4175
1 20Th Ave Se
Minot, ND
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

Farmers Union Lumber
(701) 572-8356
320 26th Street E
Williston, ND
 
Dakota Sq Mall
(701) 857-1223
2400 10Th St Sw
Minot, ND
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-20
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-20
Sun:12-18

Arrowhead Ace Hardware
(701) 839-6166
1600 2nd Ave SW
Minot, ND
 
Muus Lumber & Hardware
(701) 852-4038
2700 Burdick Expressway E
Minot, ND
 
The Home Depot
(701)282-2078
4700 17th Avenue SW
Fargo, ND
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 12:00pm-8:00pm

ACME TOOLS- Grand Forks
(701) 746-6481
1705 13th Ave North Grand Forks, ND, 58203
Grand Forks, ND
 

Coping with Inside Miters

Coping with Inside Miters

A time honored technique for applying molding to inside corners.

by Dave Munkittrick

The best technique for applying molding on an inside corner is called a coped joint. Cabinet-makers have used this joint to create great-looking inside corners for centuries. The technique involves cutting a profile on the end of the molding that fits like a puzzle piece against the adjoining piece (see above). 

To create the profile, cut a 45-degree miter on the end of the molding (Photo 1), just as you would if you were going to miter the joints. Then, use a coping saw with a fine-toothed blade to cut out the profile (Photo 2). Only the simplest moldings will allow you to complete the joint with one long cut. For abrupt direction changes, you’ll need to back out of the cut and approach it from a different angle. Use files to clean up the profiled edge and fine-tune the fit (Photo 3). 

Photo 1: Make an inside 45-degree cut to create a profiled edge. The molding should be held upside down on the saw. A stop block clamped to the saw holds the molding in place.

Photo 2: Cut the profile with a coping saw following the profile line created by the miter cut. Angle the saw back about 30 degrees as you cut along the profile to remove more wood from the back of the molding. 

Photo 3: Files fine-tune the cut. Choose a file that matches the particular profile. File and test-fit until the joint is tight.

This story originally appeared in  American Woodworker September 2005, issue #116.

Source information may have changed since the original publication date.

September 2005, issue #116

Purchase this back issue.

Click here to read the rest of the article from American Woodworker