American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Coping with Inside Miters Montgomery AL

Cabinet-makers have used this joint to create great-looking inside corners for centuries. The technique involves cutting a profile on the end of the molding that fits like a puzzle piece against the adjoining piece (see above).

The Home Depot
(334)272-8552
2312 Eastern Blvd
Montgomery, AL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Fastenal- Montgomery
334-284-6069
4560 Newcomb Ave Montgomery, AL, 36108
Montgomery, AL
 
FASTENING SOLUTIONS INC
334-284-8300
3075 SELMA HWY MONTGOMERY, AL, 36108
Montgomery, AL
 
Fastenal- Montgomery
334-244-1989
849 Lagoon Business Loop Montgomery, AL, 36117
Montgomery, AL
 
LOWE'S OF S. MONTGOMERY, ALA.
334 409-9000
1950 EASTERN BLVD. MONTGOMERY, AL, 36117
Montgomery, AL
 
The Home Depot
(334)285-1693
2710 Legends Parkway
Prattville, AL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

ABC Supply Co.,Inc/Montgomery
334-263-4755
520 Air Base Blvd. Montgomery, AL, 36108
Montgomery, AL
 
Lowe's
(334) 409-9000
1950 Eastern Blvd
Montgomery, AL
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Eastdale Mall
(334) 271-8200
1500 Eastdale Mall
Montgomery, AL
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:12-18

Ace Hardware And The Feedlot
(334) 284-1788
2050 Meriwether Rd
Pike Road, AL
 

Coping with Inside Miters

Coping with Inside Miters

A time honored technique for applying molding to inside corners.

by Dave Munkittrick

The best technique for applying molding on an inside corner is called a coped joint. Cabinet-makers have used this joint to create great-looking inside corners for centuries. The technique involves cutting a profile on the end of the molding that fits like a puzzle piece against the adjoining piece (see above). 

To create the profile, cut a 45-degree miter on the end of the molding (Photo 1), just as you would if you were going to miter the joints. Then, use a coping saw with a fine-toothed blade to cut out the profile (Photo 2). Only the simplest moldings will allow you to complete the joint with one long cut. For abrupt direction changes, you’ll need to back out of the cut and approach it from a different angle. Use files to clean up the profiled edge and fine-tune the fit (Photo 3). 

Photo 1: Make an inside 45-degree cut to create a profiled edge. The molding should be held upside down on the saw. A stop block clamped to the saw holds the molding in place.

Photo 2: Cut the profile with a coping saw following the profile line created by the miter cut. Angle the saw back about 30 degrees as you cut along the profile to remove more wood from the back of the molding. 

Photo 3: Files fine-tune the cut. Choose a file that matches the particular profile. File and test-fit until the joint is tight.

This story originally appeared in  American Woodworker September 2005, issue #116.

Source information may have changed since the original publication date.

September 2005, issue #116

Purchase this back issue.

Click here to read the rest of the article from American Woodworker