American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Coping with Inside Miters Moscow ID

Cabinet-makers have used this joint to create great-looking inside corners for centuries. The technique involves cutting a profile on the end of the molding that fits like a puzzle piece against the adjoining piece (see above).

Moscow Building Supply, Inc
(208) 882-4716
760 N Main St
Moscow, ID
 
Fastenal- Moscow
208-883-4525
1430 S. Main St Moscow, ID, 83843
Moscow, ID
 
Spence True Value Hardware
(208) 883-8131
915 E White Ave
Moscow, ID
 
Pullman Building Supply
(509) 332-2627
North 305 Grand
Pullman, WA
 
The Home Depot
(208)743-5097
2425 Thain Grade
Lewiston, ID
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

Moscow - Auth Hometown
(208) 882-8095
1410 S Blaine
Moscow, ID
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-18
Sun:12-17
Store Features
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-18
Sun:12-17

Tri-State Distributors In
(208) 882-4555
1104 W Pullman Rd, Across the Highway from the University!
Moscow, ID
 
Ace Hardware - Pullman
(509) 332-1450
1690 S Grand Ave, Wheatland Mall
Pullman, WA
 
Spence True Value Hardware
(800) 642-7392
915 E White Ave
Moscow, ID

Data Provided by:
The Home Depot
(208)388-8500
3639 E Federal Way
Boise, ID
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

Coping with Inside Miters

Coping with Inside Miters

A time honored technique for applying molding to inside corners.

by Dave Munkittrick

The best technique for applying molding on an inside corner is called a coped joint. Cabinet-makers have used this joint to create great-looking inside corners for centuries. The technique involves cutting a profile on the end of the molding that fits like a puzzle piece against the adjoining piece (see above). 

To create the profile, cut a 45-degree miter on the end of the molding (Photo 1), just as you would if you were going to miter the joints. Then, use a coping saw with a fine-toothed blade to cut out the profile (Photo 2). Only the simplest moldings will allow you to complete the joint with one long cut. For abrupt direction changes, you’ll need to back out of the cut and approach it from a different angle. Use files to clean up the profiled edge and fine-tune the fit (Photo 3). 

Photo 1: Make an inside 45-degree cut to create a profiled edge. The molding should be held upside down on the saw. A stop block clamped to the saw holds the molding in place.

Photo 2: Cut the profile with a coping saw following the profile line created by the miter cut. Angle the saw back about 30 degrees as you cut along the profile to remove more wood from the back of the molding. 

Photo 3: Files fine-tune the cut. Choose a file that matches the particular profile. File and test-fit until the joint is tight.

This story originally appeared in  American Woodworker September 2005, issue #116.

Source information may have changed since the original publication date.

September 2005, issue #116

Purchase this back issue.

Click here to read the rest of the article from American Woodworker