American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Coping with Inside Miters Oconomowoc WI

Cabinet-makers have used this joint to create great-looking inside corners for centuries. The technique involves cutting a profile on the end of the molding that fits like a puzzle piece against the adjoining piece (see above).

The Home Depot
(262)646-9160
3400 Hillside Dr
Delafield, WI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Boehm-Madisen Lumber Co.
(262) 544-4660
N16 W22100 Jericho Dr.
Waukesha, WI

Data Provided by:
The Home Depot
(262)363-7141
232 E Wolf Run
Mukwonago, WI
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

Ace Hardware of Oconomowoc
(262) 567-8288
1081 Summit Ave
Oconomowoc, WI
 
Lorleberg True Value
(262) 567-0267
900 E Wisconsin Ave
Oconomowoc, WI
 
The Home Depot
(262)717-0344
2320 W Bluemound Rd
Waukesha, WI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Kettle Moraine Hardwoods
(262) 644-8119
5261 Aurora Rd.
Hartford, WI

Data Provided by:
The Home Depot
(262)502-9840
N94 W 18375 Thunder Rdg
Menomonee Falls, WI
Hours
Mon-Sat: 8:00am-8:00pm
Sun: 9:00am-6:00pm

Kmart 3692 / Cross Merch
(262) 567-2300
1450 Summit Avenue
Oconomowoc, WI
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

Warden's Ace Hardware
(262) 646-4101
2835 Heritage Dr, walmart plaza shopping center
Delafield, WI
 
Data Provided by:

Coping with Inside Miters

Coping with Inside Miters

A time honored technique for applying molding to inside corners.

by Dave Munkittrick

The best technique for applying molding on an inside corner is called a coped joint. Cabinet-makers have used this joint to create great-looking inside corners for centuries. The technique involves cutting a profile on the end of the molding that fits like a puzzle piece against the adjoining piece (see above). 

To create the profile, cut a 45-degree miter on the end of the molding (Photo 1), just as you would if you were going to miter the joints. Then, use a coping saw with a fine-toothed blade to cut out the profile (Photo 2). Only the simplest moldings will allow you to complete the joint with one long cut. For abrupt direction changes, you’ll need to back out of the cut and approach it from a different angle. Use files to clean up the profiled edge and fine-tune the fit (Photo 3). 

Photo 1: Make an inside 45-degree cut to create a profiled edge. The molding should be held upside down on the saw. A stop block clamped to the saw holds the molding in place.

Photo 2: Cut the profile with a coping saw following the profile line created by the miter cut. Angle the saw back about 30 degrees as you cut along the profile to remove more wood from the back of the molding. 

Photo 3: Files fine-tune the cut. Choose a file that matches the particular profile. File and test-fit until the joint is tight.

This story originally appeared in  American Woodworker September 2005, issue #116.

Source information may have changed since the original publication date.

September 2005, issue #116

Purchase this back issue.

Click here to read the rest of the article from American Woodworker