American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Coping with Inside Miters Rosenberg TX

Cabinet-makers have used this joint to create great-looking inside corners for centuries. The technique involves cutting a profile on the end of the molding that fits like a puzzle piece against the adjoining piece (see above).

The Home Depot
(281)239-2777
24400 Commercial Drive
Rosenberg, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(281)242-9200
15505 SW Freeway
Sugar Land, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(281)498-6445
6800 W Sam Houston
Houston, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(281)403-1397
5900 Hwy 6 South
Missouri City, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Lowe's
(281) 232-1838
28005 Southwest Freeway
Rosenberg, TX
Hours
M-SA 7 am - 9 pm
SU 8 am - 7 pm

The Home Depot
(281)693-8420
6850 S Fry Road
Katy, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(281)870-9369
2828 South Highway 6
Houston, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(281)599-9170
1111 Fry Rd
Katy, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

LOWE'S OF ROSENBERG, TX
281 232-1838
28005 SOUTHWEST FREEWAY ROSENBERG, TX, 77471
Rosenberg, TX
 
Ace Hardware
(281) 342-5458
3714 Avenue I
Rosenberg, TX
 

Coping with Inside Miters

Coping with Inside Miters

A time honored technique for applying molding to inside corners.

by Dave Munkittrick

The best technique for applying molding on an inside corner is called a coped joint. Cabinet-makers have used this joint to create great-looking inside corners for centuries. The technique involves cutting a profile on the end of the molding that fits like a puzzle piece against the adjoining piece (see above). 

To create the profile, cut a 45-degree miter on the end of the molding (Photo 1), just as you would if you were going to miter the joints. Then, use a coping saw with a fine-toothed blade to cut out the profile (Photo 2). Only the simplest moldings will allow you to complete the joint with one long cut. For abrupt direction changes, you’ll need to back out of the cut and approach it from a different angle. Use files to clean up the profiled edge and fine-tune the fit (Photo 3). 

Photo 1: Make an inside 45-degree cut to create a profiled edge. The molding should be held upside down on the saw. A stop block clamped to the saw holds the molding in place.

Photo 2: Cut the profile with a coping saw following the profile line created by the miter cut. Angle the saw back about 30 degrees as you cut along the profile to remove more wood from the back of the molding. 

Photo 3: Files fine-tune the cut. Choose a file that matches the particular profile. File and test-fit until the joint is tight.

This story originally appeared in  American Woodworker September 2005, issue #116.

Source information may have changed since the original publication date.

September 2005, issue #116

Purchase this back issue.

Click here to read the rest of the article from American Woodworker