American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Coping with Inside Miters Van Buren AR

Cabinet-makers have used this joint to create great-looking inside corners for centuries. The technique involves cutting a profile on the end of the molding that fits like a puzzle piece against the adjoining piece (see above).

The Home Depot
(479)649-5888
5101 Phoenix Avenue
Ft Smith, AR
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Lowe's
(479) 494-4470
2120 Fayetteville Road
Van Buren, AR
Hours
M-SA 7 am - 9 pm
SU 8 am - 7 pm

Central Mall
(479) 484-9200
5111 Rogers Ave
Fort Smith, AR
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:9-21
Tue:9-21
Wed:9-21
Thu:9-21
Fri:9-21
Sat:9-21
Sun:11-18
Store Features
Mon:9-21
Tue:9-21
Wed:9-21
Thu:9-21
Fri:9-21
Sat:9-21
Sun:11-18

Yeager Ace Hardware
(479) 783-4629
2619 Rogers Ave
Fort Smith, AR
 
Yeager Hardware
(479) 646-1209
4910 Jenny Lind Rd
Fort Smith, AR
 
Yeager Ace Hardware
(479) 474-5278
1610 Main St
Van Buren, AR
 
Walrods Hardware
(479) 782-8600
2113 Midland Blvd
Fort Smith, AR
 
Lowe's
(479) 452-6000
8001 Rogers Avenue
Fort Smith, AR
Hours
M-SA 7 am - 10 pm
SU 8 am - 8 pm

LOWE'S OF FT. SMITH, ARK.
479 452-6000
8001 ROGERS AVE. FORT SMITH, AR, 72903
Fort Smith, AR
 
Meadors Lumber Company
(479) 632-2245
218 Commerce Drive
Alma, AR
 

Coping with Inside Miters

Coping with Inside Miters

A time honored technique for applying molding to inside corners.

by Dave Munkittrick

The best technique for applying molding on an inside corner is called a coped joint. Cabinet-makers have used this joint to create great-looking inside corners for centuries. The technique involves cutting a profile on the end of the molding that fits like a puzzle piece against the adjoining piece (see above). 

To create the profile, cut a 45-degree miter on the end of the molding (Photo 1), just as you would if you were going to miter the joints. Then, use a coping saw with a fine-toothed blade to cut out the profile (Photo 2). Only the simplest moldings will allow you to complete the joint with one long cut. For abrupt direction changes, you’ll need to back out of the cut and approach it from a different angle. Use files to clean up the profiled edge and fine-tune the fit (Photo 3). 

Photo 1: Make an inside 45-degree cut to create a profiled edge. The molding should be held upside down on the saw. A stop block clamped to the saw holds the molding in place.

Photo 2: Cut the profile with a coping saw following the profile line created by the miter cut. Angle the saw back about 30 degrees as you cut along the profile to remove more wood from the back of the molding. 

Photo 3: Files fine-tune the cut. Choose a file that matches the particular profile. File and test-fit until the joint is tight.

This story originally appeared in  American Woodworker September 2005, issue #116.

Source information may have changed since the original publication date.

September 2005, issue #116

Purchase this back issue.

Click here to read the rest of the article from American Woodworker