American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Crown Molding on the Tablesaw Anderson IN

Start by cutting coves that match the concave curves. These cuts require a fence clamped at an angle and several passes, with the blade raising 1/16 in. each time. Cut the cove at the bottom of the molding with the blade set at 1/4 in. and the fence at 18 degrees.

The Home Depot
(317)774-8087
3300 Conner Street
Noblesville, IN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Mounds Mall S/C
(765) 683-4600
2109 S Scatterfield Rd
Anderson, IN
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-19.5
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-17.5
Store Features
Mon:10-21
Tue:10-19.5
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-17.5

LOWE'S OF ANDERSON, IND.
765 641-2586
3335 SOUTH SCATTERFIELD RD ANDERSON, IN, 46013
Anderson, IN
 
Shumaker Electric Co.
(765) 378-7212
9044 S County Rd 800 West
Daleville, IN
 
Fastenal- Muncie
765-282-6528
5794 W. Kilgore Ave Muncie, IN, 47304
Muncie, IN
 
Fastenal- Anderson
765-643-2975
702 West 8th St Anderson, IN, 46016
Anderson, IN
 
Lowe's
(765) 641-2586
3335 South Scatterfield Road
Anderson, IN
Hours
M-SA 6:30 am - 10 pm
SU 8 am - 8 pm

Northgate True Value Hardware
(765) 642-2400
2400 Broadway St
Anderson, IN
 
Mathews True Value Home Center
(765) 778-2411
1810 Fairfield Lane
Pendleton, IN
 
Elwood - D
(765) 552-3348
1519 State Rd 37 S
Elwood, IN
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

Crown Molding on the Tablesaw

Crown Molding on the Tablesaw

by Tim Johnson

Finding factory-made crown molding to match your cherry or walnut dream project isn’t so easy. Most lumberyards only stock crown molding in pine and oak. Ordering by mail is slow and expensive, especially if you only need a few feet of molding. And there’s a good chance the molding you receive won’t match the color or the grain of the wood in your project.

The solution to these problems is simple: Make your own crown molding. Then you’ll be able to say, “I built this project by myself,” without thinking, “Well, almost.”

I’ll show you how to make classic crown molding on a tablesaw, using a general-purpose blade to shape the profile. Finishing requires a scraper, a block plane, a length of PVC pipe, sandpaper and elbow grease.

You can create almost any molding profile using this method. The molding shown here crowns the “ Grand Bookcase ”.


A Simple Procedure

To make the molding, you simply draw its profile on the ends of a blank and then cut away the waste, using the drawn-on profile to set the fence and blade height for each cut. Ideally, the cuts barely score the profile line. Planing, scraping and sanding finish the job. Cuts made too deep would require additional sanding that slightly changes the profile.

Create curved shapes by passing the blank over the blade at an angle or by adjusting the blade’s height between adjacent passes. Create flat surfaces by tilting the blade. Some cuts require turning the molding end for end or feeding it on its edge.

My saw has a left-tilting blade. If your blade tilts to the right, work from the opposite side of the rip fence and reverse the orientation of the blanks.



Transfer the Profile

Make a full-size pattern of the molding (Fig. A, below) by reducing it to 78 percent on a photocopier. (Adjust the percentage, if needed, to match the pattern to your blank’s length and width.)Use this pattern to draw the molding’s profile onto both ends of all of your molding blanks, including a couple extra blanks for test-cutting. Your blanks must all be the same width and thickness. Lengths can vary.

Photo 1: Start by cutting coves that match the concave curves. These cuts require a fence clamped at an angle and several passes, with the blade raising 1/16 in. each time. Cut the cove at the bottom of the molding with the blade set at 1/4 in. and the fence at 18 degrees. Cut the large cove at the top of the molding with the blade at 9/32 in. and the fence at 24 degrees.

Guides, which have been cut to the correct angles on a miter saw, make it easy to position the fence. Raise the blade, lay the guide against the blade’s side and lay the fence against the guide.

The fence must be angled correctly to set it at the proper distance from the blade.

Click here to read the rest of the article from American Woodworker