American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Crown Molding on the Tablesaw Dubuque IA

Start by cutting coves that match the concave curves. These cuts require a fence clamped at an angle and several passes, with the blade raising 1/16 in. each time. Cut the cove at the bottom of the molding with the blade set at 1/4 in. and the fence at 18 degrees.

Lowe's
(563) 588-8008
4100 Dodge Street
Dubuque, IA
Hours
M-SA 6:30 am - 9 pm
SU 8 am - 7 pm

Kmart 4018 / Cross Merch
(563) 588-2361
2600 Dodge St
Dubuque, IA
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Fastenal-Dubuque
563-556-7725
3185 Hughes Court Suite E Dubuque, IA, 52003
Dubuque, IA
 
Key West True Value Hardware
(563) 582-2100
2100 Stone Hill Dr
Dubuque, IA
 
Kennedy Mall
(563) 589-1500
555 John F Kennedy Rd
Dubuque, IA
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:11-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:11-18

Steve's Ace Home Garden
(563) 690-1500
3350 John F Kennedy Rd, NW Arterial & 32nd st
Dubuque, IA
 
ABC Supply Co.,Inc/Dubuque
563-557-9920
250 S. Main Street Dubuque, IA, 52003
Dubuque, IA
 
Steve's Ace Hardware
(563) 588-9755
200 S Locust St
Dubuque, IA
 
Gierke-Robinson Co- Dubuque
319 556 1185
Highway 20 West Dubuque, IA, 52003
Dubuque, IA
 
LOWE'S OF DUBUQUE, IA.
563 588-8008
4100 DODGE ST. DUBUQUE, IA, 52003
Dubuque, IA
 

Crown Molding on the Tablesaw

Crown Molding on the Tablesaw

by Tim Johnson

Finding factory-made crown molding to match your cherry or walnut dream project isn’t so easy. Most lumberyards only stock crown molding in pine and oak. Ordering by mail is slow and expensive, especially if you only need a few feet of molding. And there’s a good chance the molding you receive won’t match the color or the grain of the wood in your project.

The solution to these problems is simple: Make your own crown molding. Then you’ll be able to say, “I built this project by myself,” without thinking, “Well, almost.”

I’ll show you how to make classic crown molding on a tablesaw, using a general-purpose blade to shape the profile. Finishing requires a scraper, a block plane, a length of PVC pipe, sandpaper and elbow grease.

You can create almost any molding profile using this method. The molding shown here crowns the “ Grand Bookcase ”.


A Simple Procedure

To make the molding, you simply draw its profile on the ends of a blank and then cut away the waste, using the drawn-on profile to set the fence and blade height for each cut. Ideally, the cuts barely score the profile line. Planing, scraping and sanding finish the job. Cuts made too deep would require additional sanding that slightly changes the profile.

Create curved shapes by passing the blank over the blade at an angle or by adjusting the blade’s height between adjacent passes. Create flat surfaces by tilting the blade. Some cuts require turning the molding end for end or feeding it on its edge.

My saw has a left-tilting blade. If your blade tilts to the right, work from the opposite side of the rip fence and reverse the orientation of the blanks.



Transfer the Profile

Make a full-size pattern of the molding (Fig. A, below) by reducing it to 78 percent on a photocopier. (Adjust the percentage, if needed, to match the pattern to your blank’s length and width.)Use this pattern to draw the molding’s profile onto both ends of all of your molding blanks, including a couple extra blanks for test-cutting. Your blanks must all be the same width and thickness. Lengths can vary.

Photo 1: Start by cutting coves that match the concave curves. These cuts require a fence clamped at an angle and several passes, with the blade raising 1/16 in. each time. Cut the cove at the bottom of the molding with the blade set at 1/4 in. and the fence at 18 degrees. Cut the large cove at the top of the molding with the blade at 9/32 in. and the fence at 24 degrees.

Guides, which have been cut to the correct angles on a miter saw, make it easy to position the fence. Raise the blade, lay the guide against the blade’s side and lay the fence against the guide.

The fence must be angled correctly to set it at the proper distance from the blade.

Click here to read the rest of the article from American Woodworker