American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Crown Molding on the Tablesaw Grand Junction CO

Start by cutting coves that match the concave curves. These cuts require a fence clamped at an angle and several passes, with the blade raising 1/16 in. each time. Cut the cove at the bottom of the molding with the blade set at 1/4 in. and the fence at 18 degrees.

The Home Depot
(970)244-8577
2436 F Road
Grand Junction, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Grand Junction True Value
(970) 241-2778
1838 N 12th St
Grand Junction, CO
 
Peach Tree True Value Hdwe
(970) 245-1736
2963 North Ave
Grand Junction, CO
 
100 Mesa Mall
(970) 245-8168
2424 Highway 6 And 50
Grand Jct, CO
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:11-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:11-18

LOWE'S OF GRAND JUNCTION, CO
970 683-4760
2525 RIMROCK AVENUE GRAND JUNCTION, CO, 81505
Grand Junction, CO
 
Grand Junction - D
(970) 243-6250
2809 North Ave
Grand Jct, CO
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

ABC Supply Co.,Inc/Grand Junction
970-256-1390
310 South 12th Street Grand Junction, CO, 81501
Grand Junction, CO
 
Ace Hardware of Clifton
(970) 523-0445
569 32 Road #4
Grand Junction, CO
 
Fastenal- Grand Junction
970-243-5754
2505 Welso Avenue Grand Junction, CO, 81505
Grand Junction, CO
 
Western Implement Co Inc.
(970) 242-7960
2919 North Ave.
Grand Junction, CO
 

Crown Molding on the Tablesaw

Crown Molding on the Tablesaw

by Tim Johnson

Finding factory-made crown molding to match your cherry or walnut dream project isn’t so easy. Most lumberyards only stock crown molding in pine and oak. Ordering by mail is slow and expensive, especially if you only need a few feet of molding. And there’s a good chance the molding you receive won’t match the color or the grain of the wood in your project.

The solution to these problems is simple: Make your own crown molding. Then you’ll be able to say, “I built this project by myself,” without thinking, “Well, almost.”

I’ll show you how to make classic crown molding on a tablesaw, using a general-purpose blade to shape the profile. Finishing requires a scraper, a block plane, a length of PVC pipe, sandpaper and elbow grease.

You can create almost any molding profile using this method. The molding shown here crowns the “ Grand Bookcase ”.


A Simple Procedure

To make the molding, you simply draw its profile on the ends of a blank and then cut away the waste, using the drawn-on profile to set the fence and blade height for each cut. Ideally, the cuts barely score the profile line. Planing, scraping and sanding finish the job. Cuts made too deep would require additional sanding that slightly changes the profile.

Create curved shapes by passing the blank over the blade at an angle or by adjusting the blade’s height between adjacent passes. Create flat surfaces by tilting the blade. Some cuts require turning the molding end for end or feeding it on its edge.

My saw has a left-tilting blade. If your blade tilts to the right, work from the opposite side of the rip fence and reverse the orientation of the blanks.



Transfer the Profile

Make a full-size pattern of the molding (Fig. A, below) by reducing it to 78 percent on a photocopier. (Adjust the percentage, if needed, to match the pattern to your blank’s length and width.)Use this pattern to draw the molding’s profile onto both ends of all of your molding blanks, including a couple extra blanks for test-cutting. Your blanks must all be the same width and thickness. Lengths can vary.

Photo 1: Start by cutting coves that match the concave curves. These cuts require a fence clamped at an angle and several passes, with the blade raising 1/16 in. each time. Cut the cove at the bottom of the molding with the blade set at 1/4 in. and the fence at 18 degrees. Cut the large cove at the top of the molding with the blade at 9/32 in. and the fence at 24 degrees.

Guides, which have been cut to the correct angles on a miter saw, make it easy to position the fence. Raise the blade, lay the guide against the blade’s side and lay the fence against the guide.

The fence must be angled correctly to set it at the proper distance from the blade.

Click here to read the rest of the article from American Woodworker