American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Cube in a Cube Albert Lea MN

Crosscut a 3x3x14-in. blank into four cubes. Solid wood is best, so it doesn't look like you put the little cube in the big cube by gluing parts together. Three-in. table-leg stock works well, but you can make the cubes from 2-1/2 in. or smaller stock if you want.

The Home Depot
(507)377-9891
2400 Consul Street
Albert Lea, MN
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

Albert Lea - Auth Hometown
(507) 377-2500
2722 Bridge Ave
Albert Lea, MN
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-18
Sun:12-17
Store Features
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-18
Sun:12-17

Freeborn Lumber Co.
(507) 377-4284
971 Plaza Street W
Albert Lea, MN
 
Northwood True Value
(641) 324-1763
96 Tenth St N
Northwood, IA
 
Singelstad Do it Best Hardware
(641) 592-2800
202 N Washington
Lake Mills, IA
 
Fastenal- Albert Lea
507-377-7026
1103 Sykes Street Albert Lea, MN, 56007
Albert Lea, MN
 
Raleigh's Ace Hardware
(507) 377-8636
2525 Bridge Ave, ACROSS THE STREET FROM THE NORTHBRIDGE MALL
Albert Lea, MN
 
TRADING POST INC
(507) 448-3302
80860-110th STREET GLENVILLE, MN, 56036
Glenville, MN
 
Gambles Our Own
(507) 465-3710
108 S Broadway
New Richland, MN
 
Oak Park Mall
(507) 437-9292
1301 18Th Ave Nw Ste 206
Austin, MN
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-18
Sun:12-17
Store Features
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-18
Sun:12-17

Cube in a Cube

Cube In A Cube


“I'm a carver. I've always admired whittled curiosities like balls trapped inside a cage, but never wanted to spend the time to make them. I figured there must be some way to make a similar object with a drill press. Kids play with it like a toy, but it drives adults nuts. They think it's a puzzle. They're sure there's some way to get the little cube out of the big cube. You can't.”

Step1.
Crosscut a 3x3x14-in. blank into four cubes. Solid wood is best, so it doesn't look like you put the little cube in the big cube by gluing parts together. Three-in. table-leg stock works well, but you can make the cubes from 2-1/2 in. or smaller stock if you want.

 

Step 2.                                                                    
Mark centerlines on one face. Mark one corner of every face with a small X. You'll be drilling each hole more than one time.The X's will help register the cube in the same orientation on the drill press.

Step 3.                                                                    
Set your drill press to run at its slowest speed. Arrange the belts so the smallest diameter drive pulley turns the idler pulley. Connect the idler to the largest diameter spindle pulley.

Step 4.                                                                  
Set up your drill press with a 2 in. Forstner bit. (Use a smaller bit with a smaller block.) Position a fence and stop block so the bit drills exactly in the cube's center. Drill one hole about 1/16-in. deep.

Step 5.                                           
Set the bit's depth of cut. Draw a line from the point where a diagonal intersects the hole you made. Adjust the drill press so the bit stops about 1/16 in. above this line. This method works for any size cube and any size hole. (I've drawn the inner cube so you can see how this works.)

Step 6.
Drill holes in the end-grain sides first.

Click here to read the rest of the article from American Woodworker