American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Cube in a Cube Bangor ME

Crosscut a 3x3x14-in. blank into four cubes. Solid wood is best, so it doesn't look like you put the little cube in the big cube by gluing parts together. Three-in. table-leg stock works well, but you can make the cubes from 2-1/2 in. or smaller stock if you want.

Hermon True Value
(207) 848-2500
2402 Rt 2 Ste S
Hermon, ME
 
Fairmount True Value Hardware
(207) 942-3201
569 Hammond St
Bangor, ME
 
Schacht True Value Hdw.
(207) 862-4444
Us Rt 1a Hampden Shpg Ctr
Hampden, ME
 
Greater Northern Paving
(207) 945-9099
96 Pier St
Bangor, ME
 
Schacht True Value Hardware.
(800) 642-7392
Us Rt 1A Hampden Shpg Center
Hampden, ME

Data Provided by:
Bangor Mall
(207) 941-7200
693 Stillwater Ave
Bangor, ME
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:9-21
Tue:9-21
Wed:9-21
Thu:9-21
Fri:9-21
Sat:9-21
Sun:10-18.5
Store Features
Mon:9-21
Tue:9-21
Wed:9-21
Thu:9-21
Fri:9-21
Sat:9-21
Sun:10-18.5

Lowe's
(207) 299-9039
15 Arista Drive
Brewer, ME
Hours
M-SA 6 am - 10 pm
SU 8 am - 7 pm

Bucksport True Value
(207) 469-2451
Rr 1
Bucksport, ME
 
Broadway Hardware
(207) 945-9917
720 Broadway Ste 4
Bangor, ME

Data Provided by:
Cornith Hardware
(207) 285-3866
534 Main St
Corinth, ME

Data Provided by:
Data Provided by:

Cube in a Cube

Cube In A Cube


“I'm a carver. I've always admired whittled curiosities like balls trapped inside a cage, but never wanted to spend the time to make them. I figured there must be some way to make a similar object with a drill press. Kids play with it like a toy, but it drives adults nuts. They think it's a puzzle. They're sure there's some way to get the little cube out of the big cube. You can't.”

Step1.
Crosscut a 3x3x14-in. blank into four cubes. Solid wood is best, so it doesn't look like you put the little cube in the big cube by gluing parts together. Three-in. table-leg stock works well, but you can make the cubes from 2-1/2 in. or smaller stock if you want.

 

Step 2.                                                                    
Mark centerlines on one face. Mark one corner of every face with a small X. You'll be drilling each hole more than one time.The X's will help register the cube in the same orientation on the drill press.

Step 3.                                                                    
Set your drill press to run at its slowest speed. Arrange the belts so the smallest diameter drive pulley turns the idler pulley. Connect the idler to the largest diameter spindle pulley.

Step 4.                                                                  
Set up your drill press with a 2 in. Forstner bit. (Use a smaller bit with a smaller block.) Position a fence and stop block so the bit drills exactly in the cube's center. Drill one hole about 1/16-in. deep.

Step 5.                                           
Set the bit's depth of cut. Draw a line from the point where a diagonal intersects the hole you made. Adjust the drill press so the bit stops about 1/16 in. above this line. This method works for any size cube and any size hole. (I've drawn the inner cube so you can see how this works.)

Step 6.
Drill holes in the end-grain sides first.

Click here to read the rest of the article from American Woodworker