American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Cube in a Cube Claremore OK

Crosscut a 3x3x14-in. blank into four cubes. Solid wood is best, so it doesn't look like you put the little cube in the big cube by gluing parts together. Three-in. table-leg stock works well, but you can make the cubes from 2-1/2 in. or smaller stock if you want.

The Home Depot
(918)376-9975
9450 N 129th East Ave
Owasso, OK
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Lowe's
(918) 923-1030
1746 South Lynn Riggs Boulevard
Claremore, OK
Hours
M-SA 7 am - 9 pm
SU 8 am - 8 pm

Westlake Ace Hardware
(918) 343-3117
810 N Lynn Riggs Blvd
Claremore, OK
 
Cribbets True Value
(918) 371-3306
1008 Main St
Collinsville, OK
 
LOWE'S OF OWASSO, OK
918 274-0881
12001 E. 96TH STREET NORTH OWASSO, OK, 74055
Owasso, OK
 
Claremore - Auth Hometown
(918) 343-2500
1648 North Lynn Riggs Blvd
Claremore, OK
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:8-21
Tue:8-21
Wed:8-21
Thu:8-21
Fri:8-21
Sat:8-21
Sun:8-20
Store Features
Mon:8-21
Tue:8-21
Wed:8-21
Thu:8-21
Fri:8-21
Sat:8-21
Sun:8-20

Pixley Lumber Co
(918) 341-4223
715 W Will Rogers
Claremore, OK
 
Fastenal- Claremore
918-342-4548
1614 North Lynn Riggs Blvd Claremore, OK, 74017
Claremore, OK
 
Lowe's
(918) 274-0881
12001 E. 96Th Street North
Owasso, OK
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Pryor Lumber
(918) 825-2260
1031 West Highway 20
Pryor, OK
 

Cube in a Cube

Cube In A Cube


“I'm a carver. I've always admired whittled curiosities like balls trapped inside a cage, but never wanted to spend the time to make them. I figured there must be some way to make a similar object with a drill press. Kids play with it like a toy, but it drives adults nuts. They think it's a puzzle. They're sure there's some way to get the little cube out of the big cube. You can't.”

Step1.
Crosscut a 3x3x14-in. blank into four cubes. Solid wood is best, so it doesn't look like you put the little cube in the big cube by gluing parts together. Three-in. table-leg stock works well, but you can make the cubes from 2-1/2 in. or smaller stock if you want.

 

Step 2.                                                                    
Mark centerlines on one face. Mark one corner of every face with a small X. You'll be drilling each hole more than one time.The X's will help register the cube in the same orientation on the drill press.

Step 3.                                                                    
Set your drill press to run at its slowest speed. Arrange the belts so the smallest diameter drive pulley turns the idler pulley. Connect the idler to the largest diameter spindle pulley.

Step 4.                                                                  
Set up your drill press with a 2 in. Forstner bit. (Use a smaller bit with a smaller block.) Position a fence and stop block so the bit drills exactly in the cube's center. Drill one hole about 1/16-in. deep.

Step 5.                                           
Set the bit's depth of cut. Draw a line from the point where a diagonal intersects the hole you made. Adjust the drill press so the bit stops about 1/16 in. above this line. This method works for any size cube and any size hole. (I've drawn the inner cube so you can see how this works.)

Step 6.
Drill holes in the end-grain sides first.

Click here to read the rest of the article from American Woodworker