American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Cube in a Cube Fargo ND

Crosscut a 3x3x14-in. blank into four cubes. Solid wood is best, so it doesn't look like you put the little cube in the big cube by gluing parts together. Three-in. table-leg stock works well, but you can make the cubes from 2-1/2 in. or smaller stock if you want.

The Home Depot
(701)282-2078
4700 17th Avenue SW
Fargo, ND
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 12:00pm-8:00pm

West Acres Regional S/C
(701) 281-5800
3902 13Th Ave South Ste 600
Fargo, ND
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18

Simonson Lumber & Hdw True Value
(701) 232-3281
2400 Main Ave
Fargo, ND
 
Fastenal- Fargo
701-271-1055
3239 15th St S Suite A Fargo, ND, 58106
Fargo, ND
 
ACME TOOLS- Fargo
(701) 476-4600
920 36th Street SW Fargo, ND, 58103
Fargo, ND
 
Kmart 4057 / Cross Merch
(701) 232-8943
2301 S University Dr
Fargo, ND
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

LOWE'S OF FARGO, ND
701 433-2160
5001 13TH AVENUE SW FARGO, ND, 58103
Fargo, ND
 
Lamperts
(701) 492-0292
4115 32nd Ave Sw
Fargo, ND
 
Scheels Ace Hardware
(701) 232-8903
3202-13th Ave S
Fargo, ND
 
Nodak Stores
(701) 293-1155
3515 W Main Ave
Fargo, ND
 

Cube in a Cube

Cube In A Cube


“I'm a carver. I've always admired whittled curiosities like balls trapped inside a cage, but never wanted to spend the time to make them. I figured there must be some way to make a similar object with a drill press. Kids play with it like a toy, but it drives adults nuts. They think it's a puzzle. They're sure there's some way to get the little cube out of the big cube. You can't.”

Step1.
Crosscut a 3x3x14-in. blank into four cubes. Solid wood is best, so it doesn't look like you put the little cube in the big cube by gluing parts together. Three-in. table-leg stock works well, but you can make the cubes from 2-1/2 in. or smaller stock if you want.

 

Step 2.                                                                    
Mark centerlines on one face. Mark one corner of every face with a small X. You'll be drilling each hole more than one time.The X's will help register the cube in the same orientation on the drill press.

Step 3.                                                                    
Set your drill press to run at its slowest speed. Arrange the belts so the smallest diameter drive pulley turns the idler pulley. Connect the idler to the largest diameter spindle pulley.

Step 4.                                                                  
Set up your drill press with a 2 in. Forstner bit. (Use a smaller bit with a smaller block.) Position a fence and stop block so the bit drills exactly in the cube's center. Drill one hole about 1/16-in. deep.

Step 5.                                           
Set the bit's depth of cut. Draw a line from the point where a diagonal intersects the hole you made. Adjust the drill press so the bit stops about 1/16 in. above this line. This method works for any size cube and any size hole. (I've drawn the inner cube so you can see how this works.)

Step 6.
Drill holes in the end-grain sides first.

Click here to read the rest of the article from American Woodworker