American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Cube in a Cube Indianola IA

Crosscut a 3x3x14-in. blank into four cubes. Solid wood is best, so it doesn't look like you put the little cube in the big cube by gluing parts together. Three-in. table-leg stock works well, but you can make the cubes from 2-1/2 in. or smaller stock if you want.

The Home Depot
(515)287-7269
4900 SE 14th St
Des Moines, IA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Mccoy True Value Hdw
(515) 961-4755
216 N Howard St
Indianola, IA
 
Acme Tools-Des Moines
515-244-4189
629 SW 9th Street DES MOINES, IA, 50309
Des Moines, IA
 
The Home Depot
(563)242-0349
1850 Lincoln Way
Clinton, IA
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

The Home Depot
(515)221-2233
3700 University Ave
West Des Moines, IA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Circle B
(515) 961-5381
1700 North Jefferson
Indianola, IA
 
South Ridge Mall Ste 2002
(515) 287-4720
1111 Se Army Post Rd
Des Moines, IA
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:11-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:11-18

Scandinavian Woodshop /Sawmill
(515) 548-3449
2835 Baxter Avenue
Somers, IA

Data Provided by:
The Home Depot
(563)359-7228
920 Middle Road
Bettendorf, IA
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

Hartzell Wood Stock
(563) 566-2298
111 Center Street P.O. Box 176
Lime Springs, IA

Data Provided by:
Data Provided by:

Cube in a Cube

Cube In A Cube


“I'm a carver. I've always admired whittled curiosities like balls trapped inside a cage, but never wanted to spend the time to make them. I figured there must be some way to make a similar object with a drill press. Kids play with it like a toy, but it drives adults nuts. They think it's a puzzle. They're sure there's some way to get the little cube out of the big cube. You can't.”

Step1.
Crosscut a 3x3x14-in. blank into four cubes. Solid wood is best, so it doesn't look like you put the little cube in the big cube by gluing parts together. Three-in. table-leg stock works well, but you can make the cubes from 2-1/2 in. or smaller stock if you want.

 

Step 2.                                                                    
Mark centerlines on one face. Mark one corner of every face with a small X. You'll be drilling each hole more than one time.The X's will help register the cube in the same orientation on the drill press.

Step 3.                                                                    
Set your drill press to run at its slowest speed. Arrange the belts so the smallest diameter drive pulley turns the idler pulley. Connect the idler to the largest diameter spindle pulley.

Step 4.                                                                  
Set up your drill press with a 2 in. Forstner bit. (Use a smaller bit with a smaller block.) Position a fence and stop block so the bit drills exactly in the cube's center. Drill one hole about 1/16-in. deep.

Step 5.                                           
Set the bit's depth of cut. Draw a line from the point where a diagonal intersects the hole you made. Adjust the drill press so the bit stops about 1/16 in. above this line. This method works for any size cube and any size hole. (I've drawn the inner cube so you can see how this works.)

Step 6.
Drill holes in the end-grain sides first.

Click here to read the rest of the article from American Woodworker