American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Cube in a Cube Kailua Kona HI

Crosscut a 3x3x14-in. blank into four cubes. Solid wood is best, so it doesn't look like you put the little cube in the big cube by gluing parts together. Three-in. table-leg stock works well, but you can make the cubes from 2-1/2 in. or smaller stock if you want.

The Home Depot
(808)326-6013
73-5598 Olowalu St
Kailua Kona, HI
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-6:00pm

Fastenal- Lailua Kona
808-329-7092
73-5569 Maiau St #105 & #106 Kailua Kona, HI, 96740
Kailua Kona, HI
 
HPM Building Supply
(808) 329-1634
74-5511 Luhia St
Kailua Kona, HI
 
HPM Bldg Sply/Kailua-Kona
74-5511 Luhia Street Kailua-Kona, HI, 96740
Kailua-Kona, HI
 
Kmart 7683 / Cross Merch
(808) 326-2331
74-5465 Kamaka'Eha Ave
Kailua-Kona, HI
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

Lowe's
(808) 331-3470
75-5677 Hale Kapili Street
Kailua Kona, HI
Hours
M-SA 6 am - 9 pm
SU 7 am - 8 pm

ABC Supply Co.,Inc/Kailua Kona
808-327-0445
73-4939 Kamanu St. Kailua Kona, HI, 96740
Kailua Kona, HI
 
Kona Ace Hdwe & Crafts
(808) 329-2981
74-5500 Kaiwi St
Kailua Kona, HI
 
LOWE'S OF KONA, HI
808 331-3470
75-5677 HALE KAPILI STREET KAILUA KONA, HI, 96740
Kailua Kona, HI
 
CAPTAIN COOK ACE HARDWARE
(808) 323-2655
KEALAKEKUA RANCH CENTER
CAPTAIN COOK, HI
 

Cube in a Cube

Cube In A Cube


“I'm a carver. I've always admired whittled curiosities like balls trapped inside a cage, but never wanted to spend the time to make them. I figured there must be some way to make a similar object with a drill press. Kids play with it like a toy, but it drives adults nuts. They think it's a puzzle. They're sure there's some way to get the little cube out of the big cube. You can't.”

Step1.
Crosscut a 3x3x14-in. blank into four cubes. Solid wood is best, so it doesn't look like you put the little cube in the big cube by gluing parts together. Three-in. table-leg stock works well, but you can make the cubes from 2-1/2 in. or smaller stock if you want.

 

Step 2.                                                                    
Mark centerlines on one face. Mark one corner of every face with a small X. You'll be drilling each hole more than one time.The X's will help register the cube in the same orientation on the drill press.

Step 3.                                                                    
Set your drill press to run at its slowest speed. Arrange the belts so the smallest diameter drive pulley turns the idler pulley. Connect the idler to the largest diameter spindle pulley.

Step 4.                                                                  
Set up your drill press with a 2 in. Forstner bit. (Use a smaller bit with a smaller block.) Position a fence and stop block so the bit drills exactly in the cube's center. Drill one hole about 1/16-in. deep.

Step 5.                                           
Set the bit's depth of cut. Draw a line from the point where a diagonal intersects the hole you made. Adjust the drill press so the bit stops about 1/16 in. above this line. This method works for any size cube and any size hole. (I've drawn the inner cube so you can see how this works.)

Step 6.
Drill holes in the end-grain sides first.

Click here to read the rest of the article from American Woodworker