American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Cube in a Cube La Grande OR

Crosscut a 3x3x14-in. blank into four cubes. Solid wood is best, so it doesn't look like you put the little cube in the big cube by gluing parts together. Three-in. table-leg stock works well, but you can make the cubes from 2-1/2 in. or smaller stock if you want.

Millers Dib Home Ctr & Lumber
(541) 963-3113
307 Greenwood Street
La Grande, OR
 
La Grande - Auth Hometown
(541) 963-8451
1700 Portland Ave
La Grande, OR
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9.5-18.5
Tue:9.5-18.5
Wed:9.5-18.5
Thu:9.5-18.5
Fri:9.5-18.5
Sat:9-18
Sun:11-16
Store Features
Mon:9.5-18.5
Tue:9.5-18.5
Wed:9.5-18.5
Thu:9.5-18.5
Fri:9.5-18.5
Sat:9-18
Sun:11-16

Bare's Hometown Hardware
(541) 562-5472
206 S Main St
Union, OR

Data Provided by:
The Home Depot
(541)672-1823
3000 Aviation Drive
Roseburg, OR
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Woodcrafters
(800) 777-3709
212 NE 6th Ave
Portland, OR

Data Provided by:
D & B Supply
(541) 963-8466
10101 E 1st Street
La Grande, OR
 
Hometown Hardware
(541) 562-5472
206 S Main
Union, OR
 
The Home Depot
(541)884-0075
6451 S 6th Street
Klamath Falls, OR
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Easycreek Lumber
(541) 521-5107
PO Box 62
Lorane, OR

Data Provided by:
Goby Walnut Products
(503) 477-6744
5315 NW St. Helens Rd.
Portland, OR

Data Provided by:
Data Provided by:

Cube in a Cube

Cube In A Cube


“I'm a carver. I've always admired whittled curiosities like balls trapped inside a cage, but never wanted to spend the time to make them. I figured there must be some way to make a similar object with a drill press. Kids play with it like a toy, but it drives adults nuts. They think it's a puzzle. They're sure there's some way to get the little cube out of the big cube. You can't.”

Step1.
Crosscut a 3x3x14-in. blank into four cubes. Solid wood is best, so it doesn't look like you put the little cube in the big cube by gluing parts together. Three-in. table-leg stock works well, but you can make the cubes from 2-1/2 in. or smaller stock if you want.

 

Step 2.                                                                    
Mark centerlines on one face. Mark one corner of every face with a small X. You'll be drilling each hole more than one time.The X's will help register the cube in the same orientation on the drill press.

Step 3.                                                                    
Set your drill press to run at its slowest speed. Arrange the belts so the smallest diameter drive pulley turns the idler pulley. Connect the idler to the largest diameter spindle pulley.

Step 4.                                                                  
Set up your drill press with a 2 in. Forstner bit. (Use a smaller bit with a smaller block.) Position a fence and stop block so the bit drills exactly in the cube's center. Drill one hole about 1/16-in. deep.

Step 5.                                           
Set the bit's depth of cut. Draw a line from the point where a diagonal intersects the hole you made. Adjust the drill press so the bit stops about 1/16 in. above this line. This method works for any size cube and any size hole. (I've drawn the inner cube so you can see how this works.)

Step 6.
Drill holes in the end-grain sides first.

Click here to read the rest of the article from American Woodworker