American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Cube in a Cube La Plata MD

Crosscut a 3x3x14-in. blank into four cubes. Solid wood is best, so it doesn't look like you put the little cube in the big cube by gluing parts together. Three-in. table-leg stock works well, but you can make the cubes from 2-1/2 in. or smaller stock if you want.

Maryland Select Hardwoods - March 2010 Specials
(301) 753-6120
7470 Mason Springs Rd
La Plata, MD

Data Provided by:
The Home Depot
(703)619-5124
7710 Richmond Hwy
Alexandria, VA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

La Plata Mill & Supply Co Inc
(301) 934-8161
213 Kent Ave
La Plata, MD
 
Lowe's
(301) 539-7960
300 Rosewick Road
La Plata, MD
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

ABC Supply Co.,Inc/Waldorf
301-932-9700
44 Industrial Park Dr Waldorf, MD, 20602
Waldorf, MD
 
The Home Depot
(301)638-7222
12050 Jefferson Farm Pl
Waldorf, MD
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(301)839-9600
6003 Oxon Hill Road
Oxon Hill, MD
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Lowe's of La Plata, MD
301-539-7960
300 Rosewick Road La Plata, MD, 20646
La Plata, MD
 
Belair Road Supply
(301) 934-1800
10370 Theodore Green Blvd
White Plains, MD
 
Fastenal- Waldorf
301-632-6386
3472 Rockerfeller Ct Waldorf, MD, 20602
Waldorf, MD
 
Data Provided by:

Cube in a Cube

Cube In A Cube


“I'm a carver. I've always admired whittled curiosities like balls trapped inside a cage, but never wanted to spend the time to make them. I figured there must be some way to make a similar object with a drill press. Kids play with it like a toy, but it drives adults nuts. They think it's a puzzle. They're sure there's some way to get the little cube out of the big cube. You can't.”

Step1.
Crosscut a 3x3x14-in. blank into four cubes. Solid wood is best, so it doesn't look like you put the little cube in the big cube by gluing parts together. Three-in. table-leg stock works well, but you can make the cubes from 2-1/2 in. or smaller stock if you want.

 

Step 2.                                                                    
Mark centerlines on one face. Mark one corner of every face with a small X. You'll be drilling each hole more than one time.The X's will help register the cube in the same orientation on the drill press.

Step 3.                                                                    
Set your drill press to run at its slowest speed. Arrange the belts so the smallest diameter drive pulley turns the idler pulley. Connect the idler to the largest diameter spindle pulley.

Step 4.                                                                  
Set up your drill press with a 2 in. Forstner bit. (Use a smaller bit with a smaller block.) Position a fence and stop block so the bit drills exactly in the cube's center. Drill one hole about 1/16-in. deep.

Step 5.                                           
Set the bit's depth of cut. Draw a line from the point where a diagonal intersects the hole you made. Adjust the drill press so the bit stops about 1/16 in. above this line. This method works for any size cube and any size hole. (I've drawn the inner cube so you can see how this works.)

Step 6.
Drill holes in the end-grain sides first.

Click here to read the rest of the article from American Woodworker