American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Cube in a Cube Lebanon TN

Crosscut a 3x3x14-in. blank into four cubes. Solid wood is best, so it doesn't look like you put the little cube in the big cube by gluing parts together. Three-in. table-leg stock works well, but you can make the cubes from 2-1/2 in. or smaller stock if you want.

The Home Depot
(615)444-5472
955 S Hartman Drive
Lebanon, TN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(615)824-2391
205 N Anderson Lane
Hendersonville, TN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Fastenal- Lebanon
615-443-7612
604 E Main St Lebanon, TN, 37087
Lebanon, TN
 
Lowe's
(615) 547-7236
634 South Cumberland Street
Lebanon, TN
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

ACE Hardware of Mt. Juliet
(615) 773-9223
4110 N Mt Juliet Rd, In the old skate center
Mount Juliet, TN
 
The Home Depot
(615)889-7211
5010 Old Hickory Blvd
Hermitage, TN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(615)220-5044
551 President Place
Smyrna, TN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

LOWE'S OF LEBANON, TN
615 547-7236
634 SOUTH CUMBERLAND STREET LEBANON, TN, 37087
Lebanon, TN
 
Huskey Lumber Company Inc.
(615) 773-2333
130 Clemmonds Road
Mt Juliet, TN
 
Lowe's
(615) 773-6370
300 Pleasant Grove Rd, Suite 200
Mt. Juliet, TN
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Cube in a Cube

Cube In A Cube


“I'm a carver. I've always admired whittled curiosities like balls trapped inside a cage, but never wanted to spend the time to make them. I figured there must be some way to make a similar object with a drill press. Kids play with it like a toy, but it drives adults nuts. They think it's a puzzle. They're sure there's some way to get the little cube out of the big cube. You can't.”

Step1.
Crosscut a 3x3x14-in. blank into four cubes. Solid wood is best, so it doesn't look like you put the little cube in the big cube by gluing parts together. Three-in. table-leg stock works well, but you can make the cubes from 2-1/2 in. or smaller stock if you want.

 

Step 2.                                                                    
Mark centerlines on one face. Mark one corner of every face with a small X. You'll be drilling each hole more than one time.The X's will help register the cube in the same orientation on the drill press.

Step 3.                                                                    
Set your drill press to run at its slowest speed. Arrange the belts so the smallest diameter drive pulley turns the idler pulley. Connect the idler to the largest diameter spindle pulley.

Step 4.                                                                  
Set up your drill press with a 2 in. Forstner bit. (Use a smaller bit with a smaller block.) Position a fence and stop block so the bit drills exactly in the cube's center. Drill one hole about 1/16-in. deep.

Step 5.                                           
Set the bit's depth of cut. Draw a line from the point where a diagonal intersects the hole you made. Adjust the drill press so the bit stops about 1/16 in. above this line. This method works for any size cube and any size hole. (I've drawn the inner cube so you can see how this works.)

Step 6.
Drill holes in the end-grain sides first.

Click here to read the rest of the article from American Woodworker