American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Cube in a Cube Mccomb MS

Crosscut a 3x3x14-in. blank into four cubes. Solid wood is best, so it doesn't look like you put the little cube in the big cube by gluing parts together. Three-in. table-leg stock works well, but you can make the cubes from 2-1/2 in. or smaller stock if you want.

Edgewood Mall
(601) 250-2200
1722 Veterans Blvd
Mccomb, MS
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:13-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:13-18

Fastenal- Mccomb
601-250-6101
903-C South Locust St Mccomb, MS, 39648
Mccomb, MS
 
Covington's Ace Hardware
(601) 276-9544
721 Robb Street
Summit, MS
 
West True Value Building Supply
(800) 642-7392
602 Presley Blvd
Mccomb, MS

Data Provided by:
The Home Depot
(601)749-2180
2000 Hwy 43 South
Picayune, MS
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

LOWE'S OF MCCOMB, MS
601 250-4040
1802 PIKES POINT CIRCLE MCCOMB, MS, 39648
Mccomb, MS
 
Lowe's
(601) 250-4040
1802 Pikes Point Circle
Mccomb, MS
Hours
M-SA 7 am - 9 pm
SU 8 am - 7 pm

TYLER TOOL CO
601-876-2145
80 HIGHWAY 48 W TYLERTOWN, MS, 39667
Tylertown, MS
 
The Home Depot
(601)952-0740
6325 I-55 North
Jackson, MS
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(662)890-9470
7740 Craft Goodman Rd
Olive Branch, MS
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

Cube in a Cube

Cube In A Cube


“I'm a carver. I've always admired whittled curiosities like balls trapped inside a cage, but never wanted to spend the time to make them. I figured there must be some way to make a similar object with a drill press. Kids play with it like a toy, but it drives adults nuts. They think it's a puzzle. They're sure there's some way to get the little cube out of the big cube. You can't.”

Step1.
Crosscut a 3x3x14-in. blank into four cubes. Solid wood is best, so it doesn't look like you put the little cube in the big cube by gluing parts together. Three-in. table-leg stock works well, but you can make the cubes from 2-1/2 in. or smaller stock if you want.

 

Step 2.                                                                    
Mark centerlines on one face. Mark one corner of every face with a small X. You'll be drilling each hole more than one time.The X's will help register the cube in the same orientation on the drill press.

Step 3.                                                                    
Set your drill press to run at its slowest speed. Arrange the belts so the smallest diameter drive pulley turns the idler pulley. Connect the idler to the largest diameter spindle pulley.

Step 4.                                                                  
Set up your drill press with a 2 in. Forstner bit. (Use a smaller bit with a smaller block.) Position a fence and stop block so the bit drills exactly in the cube's center. Drill one hole about 1/16-in. deep.

Step 5.                                           
Set the bit's depth of cut. Draw a line from the point where a diagonal intersects the hole you made. Adjust the drill press so the bit stops about 1/16 in. above this line. This method works for any size cube and any size hole. (I've drawn the inner cube so you can see how this works.)

Step 6.
Drill holes in the end-grain sides first.

Click here to read the rest of the article from American Woodworker