American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Cube in a Cube Van Buren AR

Crosscut a 3x3x14-in. blank into four cubes. Solid wood is best, so it doesn't look like you put the little cube in the big cube by gluing parts together. Three-in. table-leg stock works well, but you can make the cubes from 2-1/2 in. or smaller stock if you want.

The Home Depot
(479)649-5888
5101 Phoenix Avenue
Ft Smith, AR
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Yeager Ace Hardware
(479) 474-5278
1610 Main St
Van Buren, AR
 
Yeager Ace Hardware
(479) 783-4629
2619 Rogers Ave
Fort Smith, AR
 
Lowe's
(479) 452-6000
8001 Rogers Avenue
Fort Smith, AR
Hours
M-SA 7 am - 10 pm
SU 8 am - 8 pm

Central Mall
(479) 484-9200
5111 Rogers Ave
Fort Smith, AR
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:9-21
Tue:9-21
Wed:9-21
Thu:9-21
Fri:9-21
Sat:9-21
Sun:11-18
Store Features
Mon:9-21
Tue:9-21
Wed:9-21
Thu:9-21
Fri:9-21
Sat:9-21
Sun:11-18

Lowe's
(479) 494-4470
2120 Fayetteville Road
Van Buren, AR
Hours
M-SA 7 am - 9 pm
SU 8 am - 7 pm

Walrods Hardware
(479) 782-8600
2113 Midland Blvd
Fort Smith, AR
 
LOWE'S OF FT. SMITH, ARK.
479 452-6000
8001 ROGERS AVE. FORT SMITH, AR, 72903
Fort Smith, AR
 
Yeager Hardware
(479) 646-1209
4910 Jenny Lind Rd
Fort Smith, AR
 
Meadors Lumber Company
(479) 632-2245
218 Commerce Drive
Alma, AR
 

Cube in a Cube

Cube In A Cube


“I'm a carver. I've always admired whittled curiosities like balls trapped inside a cage, but never wanted to spend the time to make them. I figured there must be some way to make a similar object with a drill press. Kids play with it like a toy, but it drives adults nuts. They think it's a puzzle. They're sure there's some way to get the little cube out of the big cube. You can't.”

Step1.
Crosscut a 3x3x14-in. blank into four cubes. Solid wood is best, so it doesn't look like you put the little cube in the big cube by gluing parts together. Three-in. table-leg stock works well, but you can make the cubes from 2-1/2 in. or smaller stock if you want.

 

Step 2.                                                                    
Mark centerlines on one face. Mark one corner of every face with a small X. You'll be drilling each hole more than one time.The X's will help register the cube in the same orientation on the drill press.

Step 3.                                                                    
Set your drill press to run at its slowest speed. Arrange the belts so the smallest diameter drive pulley turns the idler pulley. Connect the idler to the largest diameter spindle pulley.

Step 4.                                                                  
Set up your drill press with a 2 in. Forstner bit. (Use a smaller bit with a smaller block.) Position a fence and stop block so the bit drills exactly in the cube's center. Drill one hole about 1/16-in. deep.

Step 5.                                           
Set the bit's depth of cut. Draw a line from the point where a diagonal intersects the hole you made. Adjust the drill press so the bit stops about 1/16 in. above this line. This method works for any size cube and any size hole. (I've drawn the inner cube so you can see how this works.)

Step 6.
Drill holes in the end-grain sides first.

Click here to read the rest of the article from American Woodworker