American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Curved Scrapers Knightdale NC

Here's the inside scoop on those inside curves. It's a lot easier to get good results if you concentrate on creating a hook on one side only. Here's how it works: Start by creating a slight bevel on the edge (Photo 1). Then remove the wire edge (Photo 2). Finally, use your burnisher to roll the cutting hook (Photo 3).

The Home Depot
(919)217-3093
1020 Shopps At Midway
Knightdale, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Klingspor’s Woodworking Shop of Raleigh
(919) 876-0707
3141 Capital Blvd.Capital Square
Raleigh, NC

Data Provided by:
The Home Depot
(919)844-7418
9517 Strickland Rd
Raleigh, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Woodcraft - Raleigh/Durham, NC
(919) 781-1911
4317 Pleasant Valley Road
Raleigh, NC

Data Provided by:
Robbins Custom Sawing and Lumber for Natural Edge Slabs
(919) 779-0719
2200 Bull Run Drive
Apex, NC

Data Provided by:
The Home Depot
(919)878-8771
4901 Capital Blvd
Raleigh, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(919)661-1393
2540 Timber Dr
Garner, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(919)562-2202
11915 Retail Drive
Wake Forest, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(919)851-5554
2031 Walnut Street
Cary, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(919)387-6554
1000 Vision Dr
Apex, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

Curved Scrapers

Curved Scrapers



Sharpening Curved Scrapers

Q. I'm struggling to get a good cutting edge on my concave card scraper. Any tips?

A. Here's the inside scoop on those inside curves. It's a lot easier to get good results if you concentrate on creating a hook on one side only. Here's how it works: Start by creating a slight bevel on the edge (Photo 1).  Then remove the wire edge (Photo 2). Finally, use your burnisher to roll the cutting hook (Photo 3).

PHOTO 1:
File a slight bevel on the curve. With the scraper held in a vise, push a chainsaw file at a slight angle until you feel a continuous wire edge on the high side of the bevel.

PHOTO 2:
Remove the wire edge with
a super-fine diamond paddle. Because you have created a beveled edge, the wire edge will only form on the high side of the bevel.

PHOTO 3:
Use a burnisher to roll the edge and create the cutting hook. Hold the burnisher almost flat and use firm pressure to form the cutting hook. A drop or two of light machine oil helps.


Sources
Woodcraft, (800) 225-1153, www.woodcraft.com, Crown Round Scraper Burnisher, #14256, $19
Diamond Homing Stick,  #O8S15, $6. Hardware store, Chainsaw file, $3.

Click here to read the rest of the article from American Woodworker