American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Desktop Clock Daphne AL

For the clock case, you'll need 1/4-in.-thick mahogany plywood. It doesn't take much, so buy a partial sheet unless you plan to make several clocks. You'llalso need a 3/4-in. x 6-in. x 48-in. piece of mahogany lumber and a chunk of wenge. Buy a piece of wenge that’s at least 3 in. wide by 32 in. long.

The Home Depot
(251)625-0890
7100 Hwy 90
Daphne, AL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(251)955-2401
2899 S McKenzie Street
Foley, AL
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

Lowe's
(251) 621-7620
29645 Frederick Boulevard
Daphne, AL
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Jubilee Ace Home Cntr Inc
(251) 990-6665
560 Fairhope Ave
Fairhope, AL
 
LOWE'S OF MOBILE, ALA.
251 473-1880
151 EAST I-65 SERVICE ROAD SOUTH MOBILE, AL, 36606
Mobile, AL
 
The Home Depot
(251)380-0017
851 Mont Limar Dr
Mobile, AL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Lowe's of Daphne
251-621-7620
29645 Frederick Blvd Daphne, AL, 36526
Daphne, AL
 
Fairhope - Auth Hometown
(251) 990-0017
19588 Greeno Rd Hwy 98 S
Fairhope, AL
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:12-17
Store Features
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:12-17

Wigman's Ace Hardware
(251) 471-3138
1623 Dauphin Island Pkwy
Mobile, AL
 
Fastenal- Summerdale
251-947-6002
1214 Hwy 59 South Summerdale, AL, 36580
Summerdale, AL
 

Desktop Clock

Desktop Clock

This classic clock tells time, but keeps a secret.

by Jock and Susan Holmen

This clock holds a secret, and its construction involves a few secrets as well. The case is made from 1/2-in.-thick mahogany plywood. You won’t find this at most lumberyards, but you can make your own by gluing together two layers of 1/4-in. plywood. 

Another secret to building this clock is to glue the moldings to the plywood case material first and then miter the parts. It simplifies the building and sure beats mitering all the molding parts individually. Gold painted trim adds sparkle to the finished clock.

Tools and Materials

To build this clock, you’ll need a tablesaw, a planer, a router in a router table and a drill press. You’ll also need a couple of special router bits: a classic bit and a 1/8-in. round-over bit. An adjustable circle cutter is used to cut the round clock opening (see Sources, below). 

The clock is made from Honduras mahogany plywood and lumber, as well as wenge (pronounced Wen-gay or wenj). Wenge is a dark-brown tropical hardwood that nicely complements the mahogany’s reddish-brown. 

For the clock case, you’ll need 1/4-in.-thick mahogany plywood. It doesn’t take much, so buy a partial sheet unless you plan to make several clocks. You’ll also need a 3/4-in. x 6-in. x 48-in. piece of mahogany lumber and a chunk of wenge. Buy a piece of wenge that’s at least 3 in. wide by 32 in. long. It’s more than you actually need, but it’s easier and safer to cut the parts from a piece this size, rather than one that’s smaller. 

The battery-powered clock mechanism is a one-piece insert, which is simply friction-fit into a hole in the clock front. This makes it easy to change the batteries or the time. The total cost to make this clock is about $65 (see Sources, below).

Laminate the Plywood First

Cut two 32-in. x 8-in. pieces of 1/4-in. mahogany plywood (Fig. B, page 35). Notice that the grain runs the short dimension on these parts. Glue these together to form the 1/2-in. mahogany plywood needed for the clock case (Photo 1). After the glue has dried, rip the 1/2-in. plywood to 7-1/2 in. wide on the tablesaw. Take about 1/4 in. off both edges so they are straight and parallel. Next, cut the two 1/8-in. dadoes in the face of the plywood (Photo 2, Fig. A, below).

Attach the Moldings and Trim

Make the upper and lower flat trim pieces (C, D, E and F). Place spacer strips in the small dadoes in the panel to provide a stop for the flat trim to push up against, and glue the flat trim to the 1/2-in. plywood panel (Photo 3). Remove the spacer sticks before the glue dries to prevent them from getting stuck. 

Next cut a strip of mahogany for the top and bottom moldings (G, H, J and K). Use a classic router bit to shape them (Photo 4).

Click here to read the rest of the article from American Woodworker