American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Divided-Light Doors Pasco WA

Mill all the door parts to final thickness (7/8 in. for this door). Make a few extra boards the same size as the rails. Use these for making the muntins and for testing the router bit and mortising machine setups. Crosscut all the pieces a few inches long.

Whites Unfinished Furniture and Hardwoods
(509) 582-3375
2 West Kennewick Ave
Kennewick, WA

Data Provided by:
The Home Depot
(509)627-0111
2855 Duportail Street
Richland, WA
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 7:00am-8:00pm

Lowe's of Pasco, WA
509-546-7600
4520 Road 68 Pasco, WA, 99301
Pasco, WA
 
Lowe's
(509) 546-7600
4520 Road 68
Pasco, WA
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Washington True Value Hdw &furn
(509) 582-2141
6 W Kennewick Ave
Kennewick, WA
 
The Home Depot
(509)582-6697
3910 W 27th Avenue
Kennewick, WA
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 7:00am-8:00pm

Griggs Department Store
(509) 547-0566
801 W Columbia St, Near The Cable Bridge
Pasco, WA
 
MILNE FASTENING SYSTEMS
(509) 547-7834
1303 West Lewis Street Pasco, WA, 99301
Pasco, WA
 
Lowe's
(509) 736-1451
N. 1020 Colorado Street
Kennewick, WA
Hours
M-SA 6 am - 10 pm
SU 7 am - 8 pm

LOWE'S OF KENNEWICK, WA.
509 736-1451
N 1020 COLORADO STREET KENNEWICK, WA, 99336
Kennewick, WA
 
Data Provided by:

Divided-Light Doors

Divided-Light Doors

Add a masterful touch with classic glass doors. 

by Tom Caspar

Anatomy of a Divided-Light Door

Three major parts make a divided light door: stiles, rails and muntins. Every part is locked in place by a mortise-and-tenon joint. In this six-light door, the two horizontal muntins are the same length as the rails. Three short vertical muntins fit between the rails and horizontal muntins. 

Although proportions vary among furniture styles, in this door the lower rail is 1-1/2 times as wide as the top rail. All the lights are the same size and evenly divided.


Tools You’ll Use

To build these doors, you’ll need a router table and a set of special bits (see Sources, below). You’ll also need a metric ruler, tablesaw, planer, jointer and some means of making mortises. 

Design Your Door

Let’s start with some old-fashioned terms. The openings for the glass are traditionally called lights.  They’re “divided” by bars called  muntins. 

Start by drawing your door. Determine the door’s overall size, the widths of the stiles, rails and muntins, and the size of the lights. 

Next, select a set of divided-light door router bits. Each set is designed for a specific range of door thicknesses and requires a different setup, but the general steps are the same. Visit the manufacturers’ Web sites for details. We used bits from Freud ($150, see photos right). They’re suitable for doors from 13/16 to 1-1/8 in. thick with 5/8-in. or wider muntins. These bits make tenons; some other sets do not.

Start Cutting Parts

Mill all the door parts to final thickness (7/8 in. for this door). Make a few extra boards the same size as the rails. Use these for making the muntins and for testing the router bit and mortising machine setups. Crosscut all the pieces a few inches long. 

Rip and joint the stiles and rails to final width. Cut the stiles to final length. Leave the rails and muntin boards long. The muntins will be 3/4 in. wide, but don’t rip them yet. Leave them as part of a wider board.

Two matched router bits cut all the profiles. The cope cutter shapes the ends of all the rails and muntins. It also forms a short tenon and a rabbet to receive the glass. The bead cutter shapes the long edges of the stiles, rails and muntins. It also forms a rabbet.

Both bits may be adjusted to fine-tune the tenon’s thickness. You simply take apart the bit and add shims above the bearing. These shims come with the bit and are stored under the nut and washers.


Determine the Length of the Rails and Muntins

Cut every part of the door to exact length in these steps. Use the actual stiles to calculate the precise length of the rails and muntins.

Photo 1: Cut two spacers to spread the stiles to the door’s final width.

Click here to read the rest of the article from American Woodworker