American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Divided-Light Doors Rutland VT

Mill all the door parts to final thickness (7/8 in. for this door). Make a few extra boards the same size as the rails. Use these for making the muntins and for testing the router bit and mortising machine setups. Crosscut all the pieces a few inches long.

The Home Depot
(802)786-6900
299 US Rt 4 East
Rutland, VT
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Goodro True Value Of Killington
(802) 422-3469
Rt 4
Killington, VT
 
Gilmore Home Center
(802) 468-5676
Route 4 A
Bomoseen, VT
 
E.c.crosby&sons A True Value Store
(802) 293-5111
49 Mill Rd
Danby, VT
 
NeighborWorks of Western Vermont
(802) 438-2303
110 Marble Street
West Rutland, VT
 
Noble Ace
(802) 773-2758
261 N Main St
Rutland, VT
 
Nail It Down Hardware
(802) 446-2133
34 Maple Street
Wallingford, VT
 
Brandon Lumber & Millwork
(802) 247-6000
11 Grove St
Brandon, VT
 
The Hardware At Rochester
(802) 767-4200
Rt 100 Main Street
Rochester, VT
 
Ben Franklin Fair Haven
(800) 642-7392
111 E Park Pl
Fair Haven, VT

Data Provided by:
Data Provided by:

Divided-Light Doors

Divided-Light Doors

Add a masterful touch with classic glass doors. 

by Tom Caspar

Anatomy of a Divided-Light Door

Three major parts make a divided light door: stiles, rails and muntins. Every part is locked in place by a mortise-and-tenon joint. In this six-light door, the two horizontal muntins are the same length as the rails. Three short vertical muntins fit between the rails and horizontal muntins. 

Although proportions vary among furniture styles, in this door the lower rail is 1-1/2 times as wide as the top rail. All the lights are the same size and evenly divided.


Tools You’ll Use

To build these doors, you’ll need a router table and a set of special bits (see Sources, below). You’ll also need a metric ruler, tablesaw, planer, jointer and some means of making mortises. 

Design Your Door

Let’s start with some old-fashioned terms. The openings for the glass are traditionally called lights.  They’re “divided” by bars called  muntins. 

Start by drawing your door. Determine the door’s overall size, the widths of the stiles, rails and muntins, and the size of the lights. 

Next, select a set of divided-light door router bits. Each set is designed for a specific range of door thicknesses and requires a different setup, but the general steps are the same. Visit the manufacturers’ Web sites for details. We used bits from Freud ($150, see photos right). They’re suitable for doors from 13/16 to 1-1/8 in. thick with 5/8-in. or wider muntins. These bits make tenons; some other sets do not.

Start Cutting Parts

Mill all the door parts to final thickness (7/8 in. for this door). Make a few extra boards the same size as the rails. Use these for making the muntins and for testing the router bit and mortising machine setups. Crosscut all the pieces a few inches long. 

Rip and joint the stiles and rails to final width. Cut the stiles to final length. Leave the rails and muntin boards long. The muntins will be 3/4 in. wide, but don’t rip them yet. Leave them as part of a wider board.

Two matched router bits cut all the profiles. The cope cutter shapes the ends of all the rails and muntins. It also forms a short tenon and a rabbet to receive the glass. The bead cutter shapes the long edges of the stiles, rails and muntins. It also forms a rabbet.

Both bits may be adjusted to fine-tune the tenon’s thickness. You simply take apart the bit and add shims above the bearing. These shims come with the bit and are stored under the nut and washers.


Determine the Length of the Rails and Muntins

Cut every part of the door to exact length in these steps. Use the actual stiles to calculate the precise length of the rails and muntins.

Photo 1: Cut two spacers to spread the stiles to the door’s final width.

Click here to read the rest of the article from American Woodworker