American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Double-Duty Shop Stool New Castle IN

Cut the center notches and the sides of the bases using a circular saw (Photo 2). The accuracy of these cuts isn't critical, so you don't need a guide. Cut the legs and inside corners of the notches using the jigsaw.

Ace Hardware
(765) 529-3002
441 S Memorial Dr
New Castle, IN
 
New Castle - Auth Hometown
(765) 529-2958
3005 South 14Th St
New Castle, IN
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:12-17
Store Features
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:12-17

Shumaker Electric Co.
(765) 378-7212
9044 S County Rd 800 West
Daleville, IN
 
The Home Depot
(574)739-1337
4120 E Market Street
Logansport, IN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Bill Kraemer Veneers, Inc.
(812) 944-6491
2235 Croydon Pike
New Albany, IN

Data Provided by:
Fastenal- New Castle
765-521-2223
508 Broad Street New Castle, IN, 47362
New Castle, IN
 
Shirley Hardware
(765) 738-6415
313 Main St
Shirley, IN
 
Gillman Home Center
(765) 855-2600
7138 W Us Hwy 40
Centerville, IN
 
The Home Depot
(260)920-1866
403 Smaltz Way
Auburn, IN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Rockler Woodworking and Hardware #21
(317) 578-9750
8452 Castleton Corner Dr.
Indianapolis, IN

Data Provided by:
Data Provided by:

Double-Duty Shop Stool

Double-Duty Shop Stool

It's all plywood, and only uses a half sheet.

by Eric Smith

A combination stool and work support? OK, it’s an odd pair, but in my crowded shop, it makes a lot of sense. Anything that takes up less room is a good idea! The stool’s seat is divided into three pieces. When you raise the center section, you get an absolutely rigid work support that extends to 48 in. high. That’s tall enough to hold long pieces on a drill press or serve as an outfeed support for a bandsaw or tablesaw. Most commercial roller stands don’t extend this high. Just turn a simple handle—a hardware-store eye bolt—and the telescoping top locks in place.


Materials and Tools

Cut all the parts of the stool from one half-sheet (4 ft. x 4 ft.) of 3/4-in. birch plywood (about $25). Birch plywood makes the best-looking stool for the least amount of money. Its faces are free of ugly knots and its edges are virtually free of voids. But you’re free to choose any kind of 3/4-in. plywood without voids,  such as Baltic birch, marine-grade plywood or AB fir plywood. Use plywood-cutting blades in your circular saw and jigsaw to avoid splintering. 

Lay Out the Parts

1. Cut the plywood into two large rectangular pieces (Fig. B, above). Draw a centerline on the smaller piece for laying out two sets of nesting circles. Use a trammel (Fig. D, below) to draw two footrests (C, D) and two top pieces (G, H, Photo 1). Drill start holes to fit your jigsaw blade. Cut all the circles using a jigsaw.

2. Lay out the two base pieces (A, B, Fig. C, center). Use the outside edge of the smaller footrest (C) to draw the curved sections of the legs—it’s simpler than setting up the trammel. Leave a 1/2-in. separation between the two base pieces. Cut the center notches and the sides of the bases using a circular saw (Photo 2). The accuracy of these cuts isn’t critical, so you don’t need a guide. Cut the legs and inside corners of the notches using the jigsaw.

Assemble the Base

3. Test-fit the two base pieces (Photo 3). Trim the notches as needed so the parts fit easily.

4. Sand the edges of the seat and base pieces. Round the corners with a 1/4-in.-radius router bit. 

5. Slide the two base pieces together. Place the smaller footrest on the base. Predrill and countersink screw holes through the footrest and into the base (Fig. A, page 84). Screw and glue the bottom footrest to the base. 

6. Check the fit of the top footrest (D) on the base. It will be tight—trim as needed. Position the top footrest so its face grain runs the opposite way from the grain of the footrest below. Glue and clamp the top footrest to the bottom footrest (Photo 4).

7. Rip the corner braces (E, Photo 5). Flip the plywood sheet over for each succeeding 45-degree cut (Fig. E, page 90). Cut the corner braces to length.

Click here to read the rest of the article from American Woodworker